文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 电脑基础知识 > fluent用户手册摘要
侵权投诉

fluent用户手册摘要

reduction of the explicit relaxation factor to 0.25.

It is good practice to begin a calculation using the default under-relaxation factors. If the residuals continue to increase after the first 4 or 5 iterations, you should reduce the under-relaxation factors.

A cautious approach is to save a data file before making any changes to the under-relaxation factors, and to give the solution algorithm a few iterations to adjust to the new parameters. Typically, an increase in the under-relaxation factors brings about a slight increase in the residuals, but these increases usually disappear as the solution progresses. If the residuals jump by a few orders of magnitude, you should consider halting the calculation and returning to the last good data file saved.

For most flows, the default under-relaxation factors do not usually require modification. If unstable or divergent behavior is observed, however, you need to reduce the under- relaxation factors for pressure, momentum, k, and from their default values to about 0.2, 0.5, 0.5, and 0.5. (It is usually not necessary to reduce the pressure under-relaxation for SIMPLEC.) In problems where density is strongly coupled with temperature, as in very-high-Rayleigh-number natural- or mixed-convection flows, it is wise to also under- relax the temperature equation and/or density (i.e., use an under-relaxation factor less than 1.0). Conversely, when temperature is not coupled with the momentum equations (or when it is weakly coupled), as in flows with constant density, the under-relaxation factor for temperature can be set to 1.0.

For other scalar 标量,数量equations the default under-relaxation may be too aggressive for some problems, especially at the start of the calculation. You may wish to reduce the factors to 0.8 to facilitate convergence.

Note that with optimal 最佳的,理想的,优化的settings, the convergence of the coupled pressure-velocity algo-rithm will be limited by the segregated solution of other scalar equations, e.g., turbulence. For optimum solver performance, you will need to increase the relaxation factors for these equations to a value greater than the default values.

here are two methods for initializing the solution:

Initialize the entire flow field (in all cells).

Patch values or functions for selected flow variables in selected cell zones or “registers” of cells. (Registers are created with the same functions that are used to markcells for adaption.)

Before patching initial values in selected cells, you must first initialize the entire flow field. You can then patch the new values over the initialized values for selected variables.

Console控制台,主控台,;安慰,慰藉;graphics图形,图像integrate集成,结合,求积分manully手动的,用手。

Monitoring surface integrals can be used to check for both iteration convergence and mesh independence. For example, you can monitor the average value of a certain variable on

a surface. When this value stops changing, you can stop iterating. You can then adapt

the mesh and reconverge the solution. The solution can be considered mesh-independent when the average value on the surface stops changing between adaptions.

For most problems, the default convergence criterion in ANSYS FLUENT is su cient.

上一页第6页

热门文档

相关文档

  • Fluent用户手册

    Fluent用户手册_电力/水利_工程科技_专业资料 暂无评价

  • FLUENT 6.3 使用手册

    FLUENT 6.3 使用手册_IT/计算机_专业资料。Fluent 6.3.26的相关帮助文档翻译过来的使用手册Fluent 6.3 使用手册 FLUENT 6.3 使用手册 B.Case 和 Data 文件...

  • TG(fluent使用手册)

    TG(fluent使用手册)_电子/电路_工程科技_专业资料 暂无评价

  • fluent手册

    如何使用该手册 根据你对 CFD 以及 FLUENT 公司的熟悉,你可以通过各种途径使用该手册 对于初学者,建议如下: 为了对 FLUENT 的计算能力以及启动方式有所了解,最好...

  • 《FLUENT中文手册(简化版)》

    ? ? ? ? ? 本手册介绍 FLUENT 的使用方法,并附带了相关的算例。下面是本教程各部分各章节的简略概括。 第一部分: 开始使用: 描述了 FLUENT 的计算能力以及...

  • FLUENT中文帮助完整版

    注意:在 Fluent 使用手册中 "grid" 和 "mesh"是具有相同所指的两个单词 图一:基本程序结构 我们可以用 GAMBIT 产生所需的几何结构以及网格(如想了解得更多可以...

  • FLUENT软件文档集锦(五)

    Fluent UDF 高级应用技术培训的应用实例 5.ANSYS FLUENT 14.5 Battery Module Manual ANSYS FLUENT 14.5官方用户手册 6.FLUENT湍流模拟教程(EN).pdf 阐述了FLUENT...

  • fluent-v6.3-lect-08b-user-defined-functions

    fluent-v6.3-lect-08b-user-defined-functions_工学_高等教育_教育专区。...编译 (详细内容请参阅FLUENT用户手册中的介绍) UDF 代码被一次性编译成机器语言...

  • fluent经典问题3

    ,具体操作请参考 Fluent 用户手册。 34 在 FLUENT 的学习过程中,通常会涉及几个压力的概念,比如压力是相对 值还是绝对值?参考压力有何作用?如何设置和利用它? ...

  • fluent新手学习资料

    Solve->Animate->Define...,具体操作请参考 Fluent 用户手册。 34 在 FLUENT 的学习过程中,通常会涉及几个压力的概念,比如压力是相对值还是绝对值?参考压力有 ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email