ARTICLE
Template-Assisted Fabrication of FreeStanding Nanorod Arrays of a HoleConducting Cross-Linked Triphenylamine Derivative: Toward Ordered Bulk-Heterojunction Solar Cells Niko Haberkorn, Jochen S. Gutmann, ,§ and Patrick Theato ,* Institute of Organic Chemistry, University of Mainz, Duesbergweg 10-14, 55099 Mainz, Germany, Institute of Physical Chemistry, University of Mainz, Welderweg 11, 55099, Mainz, Germany, and§Max-Planck-Institut fu¨ r Polymerforschung, Ackermannweg 10, 55128 Mainz, Germany
rrays of nanometer-scale structures such as nanorods, nanowires, and nanotubes have attracted increasing attention, mainly because of the potential application in many elds of research like data storage,1 3 arti cial actuators,4,5 surfaces exhibiting special wetting probabilities,6 8 sensing,9 and optoelectronics.10 12 For example, one crucial and still very challenging part of the fabrication of high-ef cient organic solar cells is to produce a nanometer-scale interpenetrating network of a donor and an acceptor phase, with an interfacial distance smaller than the exicton diffusion length (ca. 10 20 nm) in the organic material.13 An ideal morphology that has been proposed for these cells consists of an array of vertically aligned hole-conducting polymeric nanorods attached to an electrode and surrounded by an electron-conducting material connected to a cathode or vice versa.14,15 Polymeric nanorods and nanowires can be fabricated by submicrolithography,16 electro-spinning,17 mechanical drawing,18 and template-based methods.19 For the production of highly ordered nanorod arrays the template-based approach seems to be the most suitable. Track-etched polymer membranes or block copolymer thin lms as well as anodic aluminum oxide (AAO) membranes are widely used as templates to prepare nanowires. The former usually are made by bombarding a polycarbonate sheet with nuclear ssion fragments to create damage tracks and then chemically etch these track into pores.20 The membranes
A
ABSTRACT Free-standing nanorod arrays of a thermally cross-linked semiconducting triphenylamine were
fabricated on conductive ITO/glass substrates via an anodic aluminum oxide (AAO) template-assisted approach. By using a solution wetting method combined with a subsequent thermal imprinting step to ll the nanoporous structure of the template with a cross-linkable triphenylamine derivative, a polymeric replication of the AAO was obtained after thermal curing and selective removal of the template. To obtain well-aligned and free-standing nanorod arrays, aggregation and collapse of the nanorods were prevented by optimizing their aspect ratio and applying a freeze-drying technique to remove the aqueous medium after the etching step. Because of their electrochemical properties and their resistance against organic solvents after curing, these high density nanorod arrays have potential application in organic photovoltaics. KEYWORDS: triarylamine
· semiconductive polymer(s)· template-assisted patterning· anodic aluminum oxide· nanorod(s)· organic photovoltaics
were used to fabricate arrays of conducting polymer rods but their pores are only randomly distributed and their areal density of 109 pores/cm2 is relatively low compared to other template-based methods.21,22 By using thin lms of diblock copolymers with cylindrically aligned microdomains, porous templates with areal densities in excess of 1011 pores/cm2 can be obtained after selective removal of the minor component of the block copolymer.23 27 For example, Russell and co-workers recently showed the fabrication of nanorods of electropolymerized polypyrrole by using diblock copolymers templates of polystyrene-blockpoly(methylmethacrylate).28 AAO membranes provide lateral pore densities comparable to that of block copolymer templates but they also allow a greater range of pore sizes (pore diameter and pore length) and offer a higher thermal
*Address correspondence to theato@uni-mainz.de. Received for review March 2, 2009 and accepted May 13, 2009. Published online May 19, 2009. 10.1021/nn900207a CCC:$40.75 © 2009 American Chemical Society
doc.guandang.net
VOL. 3 NO. 6 1415–1422 2009
1415

this.getHibernateTemplate().find(hql, new String[]{"test", "123"}); 返回用户名为 test 并且密码为 123 的所有 User 对象 --- 四、findByExample(Objec...
template<class elemtype> elemtype max(elemtype x,elemtype y) { return x>y?x:y; } template<class elemtype> elemtype max(elemtype x,elemtype y,elemtype...
01.分析以下程序的执行结果 #include<iostream.h> template <class T> T max(T x,T y) { return (x>y?x:y); } void main() { cout<<max(2,5)<...
iBaits中SqlMapClientTemplate的使用_IT/计算机_专业资料。iBaits中SqlMapClientTemplate的使用 iBaits SqlMapClientTemplateApache iBatis 是当前 IT 项目中使用很广泛...
? 模板的一般形式又可以写为: template < typename T1,typename T2,…typename Tn> 4、函数模板与模板函数 ? 函数模板定义由模板说明和函数定义组成。 ? 格式...
函数模板的一般定义形式是: 函数模板的一般定义形式是: template <类型形式参数表> 返回类型 FunctionName (形式参数表) { //函数定义体 } 其中的类型形式参数表...
模板 (函数模板、类模板) 实例化 实例化 模板函数 模板类实例化 对象 Object Oriented 类属参数 第二节 函数模板 函数模板不是一个完完全 函数模板 Template<...
template用法_IT/计算机_专业资料。C++-- template 的用法在程序设计当中经常会出现使用同种数据结构的不同实例的情况。例如:在一个程序中 可以使用多个队列、树...
3 TemplateDemo02.cpp 4 G:\C++\CDaima\TemplateDemo02\TemplateDemo02.cpp(11) : warning C4244: 'argument' : conversion from 'const double' to 'const ...
2、定义函数模板: 模板定义以template关键字开始,后接模板形参表(用<>括起来) ,多个模板形参用逗号隔 开。 模板形参的名字没有实际意义。 1)模板形参表:模型...
热门文档