Skin-Effect Modeling of Image Plane Techniques for Radiated Emissions from PCB Traces DHEENA MOONGILAN Bell Laboratories Innovations for Lucent Technologies Holmdel, NJ 07733
Abstract: This paper uses high frequency skin effect models to characterize the current density concentration on PCB traces and then uses image plane techniques to reduce radiated emissions. The signal trace is divided into four rectangular segments based on current density concentrations and radiated emission levels are investigated by placing image planes parallel to each segments. For thick flat parallel conductors of several skin thickness, when the separation between the signal trace and ground plane is very small, the high frequency current flow is within the inner surfaces of signal trace and ground plane and sides of the signal trace. The amount of current flow on the top of the signal trace is very small and the image plane above the signal trace has little effect on radated emissions. The radiated emission levels are measured for different trace and image plane thickness and separations and results are presented I. INTRODUCTION Most printed circuit board (PCB) designs use strip line or microstrip line structures in order to reduce high frequency radiated emissions. A strip line consists of a strip signal conductor centered in a dielectric medium between two conducting planes. The conducting plane in a PCB must be either power or ground. The microstrip line is a strip signal conductor separated from a ground or power plane by a dielectric. Microstrip structures can be implemented on a single power or ground layer which is cheaper than strip line. Implementing microstrips on outer layers of the PCB lend to easy circuit adjustments&er circuit has been fabricated. Due to the presence of air and dielectric interface, an improperly designed microstrip not only radiates but also has potential for crosstalk. For a narrow microstrip in which the trace width (w) is very small compared to the dielectric height (h), the fields are distributed around the strip similar to any isolated conductor[ 11. The dielectric discontinuity due to the airdelectric interface on the microstrip excites the current flowing on top and sides of the microstrip into higher order radiating modes. High frequency current distributions on the strip and ground plane of a microstrip have been studed by several authors[2,3]. When w>h, most of the strip current flows on the bottom and sides of the strip and the ground return current flows on the top of ground plane. The width of
the ground current spreads beyond the strip width w is shLown in Figure 1 and 3. When w>>h the current distribution tends to concentrate on the bottom of the strip and above the ground plane similar to a pulse[3]. The width of the cuirrent distribution on the strip and ground plane almost equals: w. When w/h is large, the upper part of the strip should act as electromagnetic shield. If the thickness of the strilp is increased f
urther, shielding effectiveness also increases.
I
IMRGEPLAN:
I
1 The parallel side image traces to the signal trace (see Figure l), also known as guard traces, tend to be more effective as the image traces are moved closer to the signal trace and grounded to the ground plane. The side image traces imust be placed such that it covers the ground plane spread cuirrent that extends beyond w. Most papers, to author's knowledge, on skin effect theory, address the circuit performance issues, such as crosstalk, power loss and do not address radiated emissions problems. The radiated emissions on microstrip structures have been studied by several authors using image plane theory. W i a t e d emissions were reduced effectively by reducing the circuit inductance by the method of images[4]. This paper investigates the following: (1) identifies skin effect current distributions around the traces and ground plane and by varying the conductor thickness, the radiated emissions are investigated. (2) identifies skin effect current distributions around the traces and ground plane for different conductor thickness,and by placing grounded image traces at sides of the signal trace, the radiated emissions are investigated.
I
0-7803-4140-6/97/$10.00
308

C. Using RE of MTL to deal with Shielding Effect calculation The system ...“The effectiveness of an image plane in reducing radiated emissions”, IEEE...
Modeling Radiated Emissi... 暂无评价 4页 免费 Developing a decoupling .....Introduction The strong radiated emissions caused by power plane resonance are...
Louis Missouri USA 1997 [2] Moongilan D Skin-effect modeling of image plane techniques for radiated emissions from PCB traces[C] IEEE International ...
Modeling Radiated Emissi... 暂无评价 4页 免费 Developing a decoupling .....Introduction The strong radiated emissions caused by power plane resonance are...
热门文档