文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 高等教育 > 工学 > Heat Dissipation for LED Lighting- Vapor Chamber Substrate Printed Circuit Board
侵权投诉

Heat Dissipation for LED Lighting- Vapor Chamber Substrate Printed Circuit Board

Heat Dissipation for LED Lighting: Vapor Chamber

Substrate Printed Circuit Board

Zhong Huang

Department of Control Science and Engineering Zhejiang University

Hangzhou, CHINA hz-0571@163.com

Zhong Cheng

Light Co., Ltd. Zhejiang University

Hangzhou, CHINA Led@intled.com

Mingguang Wu

Department of Control Science and Engineering Zhejiang University

Hangzhou, CHINA mgwu@iipc.zju.edu.cn

Abstract—Heat dissipation is an inevitable subject during the design of light emitting diode (LED) lighting, especially for museums and medical equipment. In this paper, a novel substrate technology for an effective solution to two major problems that affect the heat dissipation performance has been introduced. (1) The non-uniform junction temperature of the module across the LED arrays and the uneven operational temperature of LED arrays; (2) The high operational temperature caused by the accumulated heat. This new type of Vapor chamber substrate printed circuit board (PCB) consists of a thermally-conductive Vapor chamber substrate which is insulated by a dielectric layer of aluminum nitride (ALN). Circuit is formed on the dielectric layer with pulse magnetron sputtering technology. Experimental results in the form of average temperature show that the vapor chamber substrate PCB can improve the temperature uniformity. And good thermal performance for high power LED arrays can also be achieved.

Keywords-LED; heat dissipation; vapor chamber substrate PCB; magnetron sputtering technology;

quantity which is several times of the conventional lighting device as well as keep the LED junction temperature below 80°C to assure reliability and low optical decay [4]. Heat dissipation is thus an important issue in high-power LED lighting technology.

In order to improve the performance of the LED lighting, two methods for heat dissipation should be taken into account: (1) increasing the air velocity with fan around the system; (2) improving the thermal performance of LED chips package; and reducing the thermal resistance from junction to ambient [5]. In this paper, we choose the first method to solve the heat dissipation problem. There are also two approaches to improve the thermal performance of LED array system. (1) Design a new substrate which reduces the average die temperature, and improves the heat dissipation capability of LED arrays, (2) Design new substrate which makes the junction temperature of the module uniform across the LED arrays, and equalizes temperatures between the central chips and the edge chips.

For lighting systems in museums and medical appliances, LEDs are well positioned to meet the demands of the security I.INTRODUCTION

of power supply, low color temperature, high color rendering,

As the fourth generation of lighting sources, LEDs received

Light-controlled precision and durability. In this paper, we used

more and more attention in people’s daily life, which were

pulse magnetron sputtering and heat pipe technology to achieve

developed by improving luminous efficiency and integrating

a new type of vapor chamber substrate PCB, which consists of

multi-chips within limited areas life. Compared to traditional

incandescent lamps, LEDs demonstrate a number of three layers: thermally-conductive vapor chamber substrate advantages, such as long lifetime, energy efficiency, wide AIN dielectric layer and metalized layer. range of colors, durable, design flexibility, easily-dimmed, Based on heat pipe technology, the vapor chamber substrate low-voltage power supply and environmental compatibility [1]. consists of a sealed hollow tube made by aluminum (a metal The LED-array-based high-power LED lighting has three with high heat conductivity) and contains a relatively small main characteristics: 1) up to a 93% improvement in stability quantity of Acetone. The dielectric layer, an ALN thin film, over other LED-based systems; 2) up to 100-fold increase in whose thickness ranges from 33 to 35 μm is formed by light output over single LED systems; and 3) millions of depositing ALN onto the surface of the vapor chamber possible combinations of spectral output [2]. However, the substrate, and the circuit is formed above the dielectric layer efficiency of photoelectric transformation is not good enough with pulse magnetron sputtering technology. Refer to Fig. 1. because only 15 to 25 percent of input power can be transformed into light and the rest of input power dissipate as heat [3]. Especially, compact high power LED array is required to product high luminous output and not to induce the high junction temperature. The lumen output and the devices efficiency are strongly dependent on the heat dissipation capacity extracted from the package. Therefore, a qualified high-power LED lighting can dissipate heat to the ambient in

Though Higher costs, vapor chamber substrate PCB is not only much thinner but also more conductive than the conventional insulated metal substrate PCB. Results from texting experiments show that this new substrate achieves good thermal performance for high power LED arrays.

c2010IEEE978-1-4244-5046-6/10/$26.00

565

第1页

你可能喜欢

热门文档

相关文档

  • v281_浅谈LED散热材料及元件

    LED lighting lamp, including heat sink materials, heat dissipation coating ...(Vapor Chamber) (Vapor Chamber Heat Sink) LED LED (a) (a) (b) (b)...

  • LED Next Stage 2013

    Heat Dissipation Material, Light Guide Component ... Printed Circuit Board, Metal Substrate, Heat ... Measurement and Manufacturing for LED Lighting and...

  • 0.5W红色LED

    Applications Interior automotive lighting (e.g. ...printed circuit board (MCPCB) or other kinds of...ii. iii. Heat dissipation or thermal conduction ...

  • citiled-cl-824-lighting-led-datasheet

    lighting-led-datasheet.html Heat Dissipation Design CL- 824 Series Heat ...connected to an external laminated circuit board, is shown in Figure-1 ( ...

  • UV40-TDS

    Dissipation Factor, at 1MHz and 25°C per ASTM...printed circuit assembly will be when the ... sunlight or full spectrum fluorescent lighting. ...

  • B1117N-3.3中文资料

    reflow or vapor-phase reflow soldering techniques....Taking the FR-4 printed circuit board and 1/16...B1117 power dissipation is calculated as follows:...

  • July_5_2007_BG_T_Clad_vs_LED_Applications( DL Versi...

    heat dissipation (see illustration below).The key...LED lighting as the most cost or energy ...LED Chip Anode Cathode Solder Printed Circuit ...

  • B1117T-X中文资料

    reflow or vapor-phase reflow soldering techniques....Taking the FR-4 printed circuit board and 1/16...B1117 power dissipation is calculated as follows:...

  • B1117

    reflow or vapor-phase reflow soldering techniques....Taking the FR-4 printed circuit board and 1/16...B1117 power dissipation is calculated as follows:...

  • EHP-A23-RGB33-PU5-TR datasheet

    Applications Interior automotive lighting (e.g. ...printed circuit board (MCPCB) or other kinds of...ii. iii. Heat dissipation or thermal conduction ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email