显性动力分析中定义摩擦参数
EDCGEN, Option, Cont, Targ, FS, FD, DC, VC, VDC, V1, V2, V3, V4, BTIME, DTIME, BOXID1, BOXID2
Specifies contact parameters for an explicit dynamics analysis.
Option
Label identifying the contact behavior (dictates the meaning of V1 through V4).
AG — Automatic general contact.
ANTS — Automatic nodes-to-surface contact.
ASSC — Automatic single surface contact.
ASS2D — Automatic 2-D single surface contact (applicable only with the Cont and FS arguments).
ASTS — Automatic surface-to-surface contact.
DRAWBEAD — Drawbead contact
ENTS — Eroding nodes-to-surface contact.
ESS — Eroding single surface contact.
ESTS — Eroding surface-to-surface contact.
FNTS — Forming nodes-to-surface contact.
FOSS — Forming one way surface-to-surface contact.
FSTS — Forming surface-to-surface contact.
NTS — Nodes-to-surface contact.
OSTS — One way surface-to-surface contact.
RNTR — Rigid nodes to rigid body contact.
ROTR — Rigid body to rigid body (one way) contact.
SE — Single edge contact.
SS — Single surface contact.
STS — Surface-to-surface contact.
TDNS — Tied nodes-to-surface contact.
TSES — Tied shell edge-to-surface contact.
TDSS — Tied surface-to-surface contact.
TNTS — Tiebreak nodes-to-surface contact
TSTS — Tiebreak surface-to-surface contact.
Cont
Contact surface identified by a component name [CM] , a part ID number [EDPART], or an assembly ID number [EDASMP]. If a component name is input, the component must contain nodes that represent the contact surface (assemblies are not valid for a component name). Alternatively, a part number may be input that identifies a group of elements as the contact surface, or an assembly number may be input containing a maximum of 16 parts. The assembly ID number must be greater than the highest number used for the part ID. Cont is not required for automatic general contact, single edge contact, and single surface contact options (Option = AG, SE, ASSC, ESS, and SS). If Option = ASS2D, only part assemblies are valid.
Targ
Target surface identified by a component name [CM] , a part ID number [EDPART], or an assembly ID number [EDASMP]. If a component name is input, the component must contain nodes that represent the target surface (assemblies are not valid for a component name). Alternatively, a part number may be input that identifies a group of elements as the target surface, or an assembly number may be input containing a maximum of 16 parts. The assembly ID number must be greater than the highest number used for the part ID. Targ is not defined for automatic general contact, single edge contact, automatic single surface contact, eroding single surface contact, single surface contact, and automatic 2-D single surface contact options (Option = AG, SE, ASSC, ESS, SS, and ASS2D).
FS
Static friction coefficient (defaults to 0).
FD
Dynamic friction coefficient (defaults to 0).
DC
Exponential decay coefficient (defaults to 0).
动力学分析中一般不予考虑 。通过规定带有摩擦性能的接触表面 单元和间隙单元,可...对于 thin-film fluid 行为的 特殊情形,可以为结构计算阻尼参数,并且用于后续的...
计及齿面摩擦的直齿轮动力学分析_机械/仪表_工程科技_专业资料。振第 31 卷...齿轮相关参数 由此可以定义摩擦力方向系数: (α C -α A )- mod( Ω p ...
本 章将概要地讲述一下显式动态分析中定义物理上...第三步:定义摩擦系数参数 接触摩擦系数是由静态摩擦...刚性体接触(RNTR 和 ROTR)通常用于多刚体动力学,在...
动力学分析中的阻尼问题_机械/仪表_工程科技_专业...包括由于材料分子之间的摩擦引起 的内阻尼机制、构件...材料阻尼是在材料参数里面进行定义的,材料 阻尼又叫...
应该注意的是,在进行内容分析时,研究者的主要兴趣并不在于各种参数、变量,而 ...(proximity analysis) 关心文本里显性概念的共现(concurrence) ,通常是定义一个...
4 动力学 第一节: 定义和目的什么是动力学分析? ...库仑或干摩擦阻尼 M1-26 动力学 - 基本概念和...有助于在其它动力分析中估算求解控制参数(如时间步长...
注:必须将摩擦用于凸轮从动连接副才能力平衡分析中计算凸轮滑动测量。 二、3D ...卡 【从动图元】:用于定义伺服电动机要驱动图元类型:连接轴、点和面等几何参数...
结构动力学和结构静力学中对结构体系自由度定义 的...结构的运动状态仅需要一个几何参数即可以确定 分析单...阻尼来源(物理机制): (1)固体材料变形时的内摩擦,...
动力学12章第一讲_工学_高等教育_教育专区。1 ...这个定义与“平面结构的几何组 成分析”一章中提及...结构在变形过程中材料内部有摩擦,称“内摩擦”,耗散...
比例常数 m 就是摩擦系数; Training Manual DYNAMICS 11.0 – 动力学分析中一般不予考虑。 三种形式阻尼的定义方法 ANSYS 允许上述所有三种形式的阻尼 Training ...
热门文档