我们把这点叫做焦点。
When the piece of a (mathematically infinite) surface of paraboloid is cut off, a parabolic reflector or mirror is gained. Cutting off (cropping) can be carried out in many ways, but all of them can be classified in two groups: those whose surface of cropping is perpendicular on the axis of symmetry, and those whose surface of cropping are not perpendicular. When the plane that cuts off paraboloid is
perpendicular on the axis of symmetry, a round segment of paraboloid is gained, whose focus is in the center, i.e. on the axis of symmetry on certain distance from geometric center of the surface, depending on the position of the cropping plane. Usually, the distance of the cropping plane is smaller than the equivalent focus and therefore in majority of dishes focus resides outside of the opening of the dish. The segment gained in this way is classic parabolic antenna.
截取一个(无限大的)抛物面的某一部分,就得到了一个抛物面反射器或曰抛物面镜。切割方法有多种,但基本分为2类:一类切割面是垂直于对称轴的,另一类是不垂直的。当抛物面切割面垂直于对称轴,就得到一个圆形的抛物面,它的焦点位于正中央,即对称轴上距离抛物面几何中心一定距离的地方,(取决于截取平面的位置)。
通常截面(到抛物面几何中心)的距离比等效焦点(到抛物面几何中心)的距离要小,因此大多数焦点位于抛物面口径面的外面。用这种方法得到的截面就是标准的抛物面天线。
All paraboloid segments gained in this way have one parameter by which they may be grouped regarding characteristics. That is the ratio between focal distance from center (F) and diameter of the segment of parabolic surface (D). All parabolic antennas that have equal ratio F/D may be illuminated by the same feed regardless its diameter, i.e. whether they are large or small, because their all other geometric dimensions are proportional, too. The ratio F/D is also crucial in determining the characteristics of the feed that will illuminate the dish. The reason for this is that ratio F/D determines the angle the edges of the parabola are seen from the focus. The smaller the ratio F/D, the deeper the dish is and this angle is greater, and vice versa, the greater the F/D ratio, the shallower the dish is and the angle are smaller. Since feed needs to be
constructed in the way that it radiates only in the direction of the parabola, and that in all other directions it radiates as little as possible, this means that the ratio F/D, also determines the optimal radiation diagram of the feed. Hence, every F/D has its optimal feed, regardless all other dimensions! Therefore, when the optimal feed for a parabola is determined, the only thing that matters is its F/D!
所有用这种方法获得的抛物面有一个特性(并以此特性分类),即焦距(F)和抛物面口径面的直径(D)的比值,所有的F/D比率相同的抛物面天线,不管其直径是否相同,都可以使用相同的馈源。也就是说,不管它们的大小,因为它们其它的几何尺寸也是成比例的。在决定典型照射馈源时,F/D的比率也是决定性因素。原因就是F/D的比率限定了抛物线焦点到边缘的角度。口径面深的F/D比率小,角度就大。反之亦然,浅的口径面,F/D比率大,角度就小。因为馈源必须向抛物面四周方向辐射,而其它方向照射要尽可能小,这就意味着F/D的比率也决定了馈源的最佳辐射方向图。因此,每一个F/D都有自己的最佳馈源,无论其它的尺寸如何。为此,当抛物面的最佳馈源确定之后,唯一一件重要的事
本文介绍用改进型3D角反射天线, 为6厘米业余无线电通信频段STA卫星电视 或WLAN频段5.8GHz频道的偏馈抛物面天线作馈源。 Introduction 引言 The problems that occur...
本文介绍用改进型3D角反射天线, 为6厘米业余无线电通信频段STA卫星电视 或WLAN频段5.8GHz频道的偏馈抛物面天线作馈源。 Introduction 引言 The problems that occur...
热门文档