40GHZ PLL in 90nm。
A 40-GHz Frequency Divider in 90-nm CMOS
Technology
Muhammad Usama and Tad. A. Kwasniewski
Department of Electronics, Carleton University 1125 Colonel By Drive, Ottawa ON, K1S 5B6 Canada.
{musama, tak}@doe.carleton.ca
Abstract-This paper presents the design of a high-speed wide-band frequency divider. The divider core is formed with a low voltage swing current mode logic (CML) structure, which enables high frequency operation at very low power dissipation. The divider exhibits very wide locking range from 4GHz - 41GHz, and it has an input sensitivity of -31dBm at 30GHz. The divider core draws only 750µA from a 1.2V supply. Post layout simulation results in 90-nm CMOS technology are provided.
I. INTRODUCTION
Frequency dividers are used in many communications applications such as frequency synthesizers, timing-recovery
circuits, and clock generation circuits. In a phase locked loop (PLL) a frequency divider is employed within the loop to divide down the local oscillator frequency and to provide the
programmability of the synthesizer. Frequency divider is one of the most critical blocks of the system because it operates at [6]-[11], [13], and [14]. the highest frequency. In particular, the power reduction of the frequency divider in the first stage is effective in realizing a This paper presents the design of a CML based frequency low-power PLL. This is the key point for the high-speed divider in a state-of-the-art 90-nm CMOS technology. The operation and low power consumption. The phase noise presented divider achieves not only a very high operating generated by the divider can affect the synthesizer noise frequency but reasonably low power dissipation. The divider performance within the PLL band, especially if a high division structure and its operation are described in Section-II. Post factor is used. In fact, the divider noise power is multiplied by layout simulation results in 90-nm CMOS technology are also the square of the division factor, when it is transferred to the provider in Section-III along with a comparison of the PLL output [1]. presented divider with other recently published results. Digital frequency dividers are the most popular divider structures in use today. They offer divider ratio programmability, higher division ratios and easier digital
II. DIVIDER STRUCTURE
control. The fundamental element of a digital frequency
Conventionally for a divider application, two identical CML divider is a D-type flip-flop, or two level-sensitive latches in a
master-slave configuration [2]. These dividers achieve a latches are used in a master-slave configuration as shown in broader bandwidth than other types of dividers in low to Fig. 1. Because of the parasitic capacitance of the transistors of medium range of frequencies. High-speed digital frequency sample circuit, the tail current must be sufficiently high to dividers are typically implemented using the current mode achieve a wider range of linearity, a higher slew rate and a logic (CML) latches. The CML lathes exhibit better larger transconductance. On the other hand the hold circuit performance than other clocked storage elements. Large does not need such a large bias current. These conflicting frequency ranges are not therefore uncommon in these dividers requirements can not be reconciled in conventional CML latch
design because they have only a single constant current source. that use CML style [12].
With the aggressive scaling of CMOS transistors, It is possible to simplify the usual CML latch clocking multi-gigahertz dividers are now realizable in CMOS structure by employing a single clock transistor pair to switch technologies. Several high-speed frequency dividers in modern

the current between the sample and hold pair of the master and
slave latches [2]. This new configuration uses a single bias
1-4244-0417-7/06/$20.00 ©2006 IEEE
41
30.3 Performance Variability of a 90GHz Static CML Frequency Divider in 65nm SOI CMOS A frequency divider is an essential and critical building block in...
A Low Power 440-MHz Pulse-Swallow-Divider Frequency Divider_IT/计算机_专业...Lam and B. Razavi, "A 2.6-GHz/5.2-GHz frequency synthesizer in 0.4...
explained using the special case of N = 2, where N is the divider ...spectrum of 40GHz where input frequency of the proposed DLL is 4.4445GHz...
在传统数字时钟分频器中,为获得 90°相位差的时钟信号进行异或, 输出相 应的...A 40-GHz Frequency Divider in 0.18?m CMOS technology [J]. IEEE J. ...
WU et al.: DUAL-FREQUENCY WILKINSON POWER DIVIDER 109 III. SIMULATION AND EXPERIMENT An dual-frequency Wilkinson power divider is designed for 1 GHz and...
A 1.8V 3mW 16.3 GHz frequency divider in 0.25μm CMOS[J].ISSCC.Frequency Sysnthesizers and dividers, 2000.PAPER TP.12:196-197. [7] Joseph M.C...
signal of 622 MHz and outputs a signal with a frequency of 10 GHz. It...It exploits the readily available quadrature signals of the last divider ...
Abstract—A 1.1-GHz fractional-N frequency synthesizer is implemented in 0...Fig. 10. Frequency divider using asynchronous counters and timing diagram = ...
A lumped element, 1.8-GHz Wilkinson power divider on CMOS grade Si using...is the angular frequency, and is the velocity of light in vacuum, is de...
A 1.1-GHz CMOS fractional-N frequency synthesizer with a 3-b third-order...Fig. 10. Frequency divider using asynchronous counters and timing diagram = ...
热门文档