文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 电脑基础知识 > RIP中default information originate的使用及5种传递默认路由的方法!
侵权投诉

RIP中default information originate的使用及5种传递默认路由的方法!

下面我们在R2,R3之间启用EIGRP,在R3上起一个loopback接口,并宣告到EIGRP中,这时R2可以学习到3.3.3.0,在R2上建立ACL匹配从R3学习到的这条路由,随后建立route-map并调用ACL,同样最后在R2的RIP进程中 的default-information originate命令后面调用这个route-map。

r2#

router eigrp 90

network 23.0.0.0 0.0.0.255

no auto-summary

r3#

int lo0

ip add 3.3.3.3 255.255.255.0

no sh

exit

router eigrp 90

network 3.3.3.0 0.0.0.255

network 23.0.0.0 0.0.0.255

no auto-summary

r2#sh ip rou

1.0.0.0/24 is subnetted, 1 subnets

R 1.1.1.0 [120/1] via 12.0.0.1, 00:00:05, Serial1/0

2.0.0.0/32 is subnetted, 1 subnets

C 2.2.2.2 is directly connected, Loopback0

3.0.0.0/24 is subnetted, 1 subnets

D 3.3.3.0 [90/2297856] via 23.0.0.3, 00:01:42, Serial1/1

23.0.0.0/24 is subnetted, 1 subnets

C 23.0.0.0 is directly connected, Serial1/1

12.0.0.0/24 is subnetted, 1 subnets

C 12.0.0.0 is directly connected, Serial1/0

R2

access-list 1 permit 3.3.3.0 0.0.0.255

route-map WY permit 10

match ip address 1

router rip

version 2

network 12.0.0.0

default-information originate route-map WY

no auto-summary

r1#sh ip rou

1.0.0.0/24 is subnetted, 1 subnets

C 1.1.1.0 is directly connected, Loopback0

12.0.0.0/24 is subnetted, 1 subnets

C 12.0.0.0 is directly connected, Serial1/0

R* 0.0.0.0/0 [120/1] via 12.0.0.2, 00:00:01, Serial1/0 /这时R2向R1传递一条默认路由

r3(config)#int lo0

r3(config-if)#shutdown /在R3上关闭这个loopback接口

r1#sh ip rou

1.0.0.0/24 is subnetted, 1 subnets

上一页第3页

你可能喜欢

热门文档

相关文档

  • RIP传递默认路由的5种方法

    RIP传递默认路由的5种方法_计算机硬件及网络_IT/计算机_专业资料。RIP 传递...同样最后在 R2 的 RIP 进程中 的 default-information originate 命令后面调用...

  • RIP传递默认路由方法

    介绍rip介绍rip隐藏>> RIP 传递默认路由方法 (共5种) 图:关于传递默认路由的实验都是以下这个图 RIP 传递默认理由方法 1:default-information originate R1: ...

  • 向RIP网络注入默认路由

    向 RIP 网络注入默认路由的三种方法; 静态路由 2、 IP DEFAULT-NETWORK 命令特征; 3、 重分布静态路由到 RIP 网络; 4、 DEFAULT-INFORMATION ORIGINATE 命令...

  • 默认路由

    在 RIP 中,默认路由采用 default-information originate 方式向其他路由器注入。 2。在 OSPF 中,分几种情况: ⑴向常规区域中注入默认路由,采用 default-information...

  • CCNA 第二学期第四章考试题及答案

    最好在 或哪一组路由器上配置默认路由并使用 default-information originate 命令...debug ip rip show ip route show ip interface show ip protocols debug ip ...

  • 默认路由发布

    在 RIP 中,默认路由采用 default-information originate 方式向其他路由 器注入。 2。在 OSPF 中,分几种情况: ⑴向常规区域中注入默认路由,采用 default-...

  • RIP笔记

    RIP 默认路由下放(5 种) 1、default-information originate---推荐方法 Router rip Default-intformation originate---进城下直接下放默认路由 ! Show ip route 2...

  • 实验5 RIP路由基本配置

    4、清除启动配置并将路由器重新加载为默认状态。 5、配置路由器使用RIPv2版本。...HQ(config-router)#default-information originate 将0.0.0.0/0静态 默认通告...

  • 静态路由与RIP实验

    在路由器 R3 上启用默认路由,让内部网络可以访问 Internet。 命令:R3(config)#router rip R3(config-router)#default-information originate 6. 在路由器 R1 ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email