
SINOPEC TCC
弯管的夹套组焊,应在主管弯曲完毕并经探伤合格后进行。The
jacket assembling and welding for the bend shall be proceeded
after the main pipe bending is completed and is qualified
through testing.
输送熔融介质管道的内表面焊缝,应平整光滑,不行有突出的焊
瘤。The inner surface weld of the piping for transporting
molten medium shall be level and smooth and must not have
protruded welding knob.
当夹套管组装有困难时,套管可采用剖分组焊的形式,其复原焊
接应保证质量。When the jacketed pipe is difficult for
assembling, the jacket may use the form of split-combined
welding and the restoration welding shall ensure the
quality.
夹套弯管的套管和主管,应保证其同轴度,偏差不得超过3mm。The
jacket pipe and the main pipe of the jacketed bend shall be
ensured for the concentricity and the deviation must not
exceed 3mm.
e. 管线组对Alignment of Piping
管线组对前必须开设坡口,组对时坡口及其管端内外表面20mm范
围内的油污、毛刺等杂物清理干净。Prior to alignment, make
bevels. It is required to remove any oil, grease, burr, and
other matters from the bevel, and the areas of 20mm on both
interior and outer surfaces of pipe neighboring to the weld.
对接缝组对应符合下表要求。Alignment of weld seam shall
上最大的聚四氢呋喃生 产公司,总生产能力达到 l8.8 万吨/年,约占世界聚四氢呋喃总生产能力的 33.5l%,分别在美国、德国、日本、韩国和中国大陆建有生产装置...
031 河南省安装集团有限责任公司鹤壁聚四氢呋喃项目部 2 河南能源精细化工有限公司年产 6 万吨聚四氢呋喃项目工程火炬管道安装工程施 工方案 一、工程概述河南能源...
聚四氢呋喃,又名聚四亚甲基醚二醇,是生产热塑性弹性体如聚酯(HYTRELO) 、聚氨酯(弹性纤维)的 重要软化段。THF 与阳离子引发剂反应后,生成聚四氢呋喃。 工业上...
巴斯夫在上海 建聚 四氢映喃和四氢吠喃装置巴斯夫公司在上海潜径 化学 工业区建聚四氢峡喃 ! 州; ? ∑ ] 和四氢 吠喃 , ?∑ ! ] 一体 化装 置 ,,...
聚四氢呋喃PTMEG简介_能源/化工_工程科技_专业资料。聚四氢呋喃PTMEG简介项目名称 公司名称 介绍人 聚四氢呋喃简介 聚四氢呋喃简介 华陆工程科技有限责任公司 ...
聚四 氢呋 喃在 高 真空 下进 .%f ;最行 蒸馏 脱除低 分子 齐聚 物, ...『 用解 聚单 元将 聚 四氧 呋哺分 解为 四氛呋喃 ;7 装置 ()投资 ...
聚四氢呋喃及其下游产品的开发应用_能源/化工_工程...生产方法一般是使用氟磺酸 ( HSO3 F) 作催化剂 ...并计划在中国再建设 7000t/ a Spandex 装置。D ...
而另一方面是聚四 氢呋喃生产技术的进步 ,装置...In : Mark H F ,Bikales N , ing[M] . 2nd... 999感冒灵市场营销方案 汽车品牌的足球世界杯营销 ...
国家应用化学科研 中心技术 ,建成 国内首套 l0吨/ 0 年聚四氢呋哺生产装置 ,5 结束 了 我国无 聚四氢呋喃生产的历史 ,F 于生产成本等方 }1 氢呋喃项 ...
合 成工 艺是将 正丁烷 直接 用 四氢 呋喃 生产 装置 ,国内需 求基 高,...国 内现 已投产 的聚 四氢呋 喃 7万吨 ,但实际产量只有 06f2.1.1 5...
热门文档