文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > Mechanically Flexible and Multifunctional Polymer-Based
侵权投诉

Mechanically Flexible and Multifunctional Polymer-Based

doc.guandang.net

Mechanically Flexible and Multifunctional Polymer-Based

doc.guandang.net

COMMUNICATION

echanically Flexible and Multifunctional Polymer-Based M

Graphene Foams for Elastic Conductors and Oil-Water Separators

Chao Wu ,Xingyi Huang ,* Xinfeng Wu ,Rong Qian ,and Pingkai Jiang *Graphene, a two-dimensional (2D) sheet of covalently bonded carbon atoms, has gained tremendous attention recently owing to its excellent physical properties such as extremely high elec-[1,2[1trical conductivity, ] high thermal conductivity, ] excellent [3[4mechanical exibility, ] large speci c surface area, ] and high

[5thermal and chemical stability. ] Such unique properties qualify

the graphene sheets as a promising source for applications in

[6–8[9,10energy storage, ] high performance electronics and sensors ]

[11as well as oil cleanup. ] One important and effective route to

employ graphene sheets for these applications is to construct

[12–23macroscopic three-dimensional (3D) graphene foams. ]

Recently, several methods have been reported for the fabrication of graphene foams. Among them are hydrothermal and chem-[13–19[20ical reduction, ] electrochemical synthesis, ] and growth

[2,21–23]of chemical vapor deposition (CVD). However, so far

the reported graphene foams generally have the disadvantages of brittle mechanical performances and are easily irreversibly

[7,14–20]damaged under mechanical deformations. This restricts

the applications of graphene foams as elastic conductors in the eld of exible electronic devices such as sensors, actuators,

[24and loudspeakers. ] Moreover, the previously reported methods

require highly time, cost, and energy-consuming cryodesiccation or CVD procedures, rendering a large-scale production of gra-[13–23phene foams substantially dif cult. ] Therefore, it remains

a challenge to develop a simple and effective synthetic route for graphene foams with excellent physical properties.

Herein we report a novel strategy for the fabrication of

ordered and exible polymer-based graphene foams (PGFs) by self-assembly of graphene sheets on a 3D polymer skeleton. This assembly process is rst conducted in aqueous solution using graphene oxide (GO) as the source of graphene, and then completed by a simple oven drying process, indicating the facile and low-cost solution of this approach for fabri-cating large-sized graphene foams. The resulting PGFs possess

C. Wu, Dr. X. Huang, X. Wu, R. Qian, Prof. P. Jiang

Department of Polymer Science and EngineeringShanghai Key Lab of Electrical Insulation and Thermal Aging

Shanghai Jiao Tong University Shanghai ,200240 ,P. R. China E-mail: xyhuang@sjtu.edu.cn; pkjiang@sjtu.edu.cn Dr. X. Huang, Prof. P. Jiang

Shanghai Engineering Center for Material Safety of Nuclear Power EquipmentShanghai Jiao Tong UniversityShanghai ,200240 ,P. R. China DOI: 10.1002/adma.201302406 5658

polymer skeletons, which effectively support graphene foams.

This unique structure not only maintains the physical proper-ties of graphene foams, but also effectively transfers load from graphene sheets to polymer skeletons under mechanical defor-mations. As a consequence, the PGFs exhibit high conductivity and hydrophobicity, outstanding mechanical properties, and excellent cycle performances, thus holding great potential as elastic conductors and oil-water separators.

The overall preparation procedures of the PGFs are illustrated in Figure 1 a, mainly including three steps. First, a commercial polyurethane foam was immersed in the GO solution with hydrazine by a squeezing and vacuum degassing procedure. GO is used as the source of graphene because it is economically

[25,26obtained to a large extend. ] Then, graphene sheets were

assembled on the polyurethane skeletons into a 3D graphene-based hydrogel by in-situ reduction of GO, with a color change from yellow to black. During the reduction procedure, the oxygen-functionalized groups of GO were removed. Thus, the interaction forces between GO sheets were transformed from electrostatic repulsion to –π attraction, leading to the assembly π

of graphene sheets around the skeletons in the foams. Finally, the resulting monolithic hydrogel was directly dried to yield the PGFs. It should be noted that the drying atmosphere can either be air or vacuum and that cryodesiccation is not neces-sary. This process is very simple and convenient without using any organic solvents, thus a large-sized PGF (e.g., 200 × 100 ×

3 60 mm ) could be produced easily, as shown in Figure S1, Sup-porting Information.

The morphology and structure of the as-prepared PGFs

were investigated by eld emission scanning electron micros-copy (FE-SEM). As shown in Figure 1 b-d, PGFs show an interconnected, porous 3D network structure with continuous macropores of hundreds of micrometers. The morphology of PGFs is similar to that of polyurethane foams, but the skeletons of the network exhibit a crinkled and rough texture associated with the presence of exible graphene sheets. This indicates that graphene sheets were assembled around the polyurethane frameworks during the reduction process. After the removal of the polymer framework by pyrolysis of PGFs under nitrogen atmosphere, they remain as a 3D scaffold structure. Figure 1 e displays a typical SEM image of the obtained graphene foams. Although a small shrinkage of the overall frameworks occurs, the majority of graphene sheets is still overlapped and linked between each other forming the wall of the foams. Interest-ingly, PGFs still remain as an entire framework when burned in air, while the pristine polymer foams vanish after burning (Figure S2). The graphene content of PGFs could be readily

Mechanically Flexible and Multifunctional Polymer-Based

tuned by simply adjusting the concentration of GO in the

wileyonlinelibrary.com© 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Mechanically Flexible and Multifunctional Polymer-Based

Adv. Mater. 2013, 25, 5658–5662

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email