文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy
侵权投诉

Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy

Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy

Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy

Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy

Simulation and Experimental Investigation for the End Milling Process of

7075-T7451 Aluminum Alloy

C. K. Wanga, G. H. Qinb,

Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy

D. Luc and S. Q. Xind

School of Aeronautical Manufacturing Engineering, Nanchang Hangkong University, Nanchang

Jiangxi, 330063, China

awangcongkang1@126.com, bqghwzx@126.com, cludong80@gmail.com, dxinshunq@163.com Keywords: finite element analysis, oblique cutting, milling force, aluminum alloy

Abstract. During the milling operation, milling forces are the main factor to cause the machining deformation of the workpiece. The flow stress of Al 7075-T7451 was first described as a function of strain, stain rate and temperature in order to obtain the true behavior in machining process. Second, a finite element method of milling process of Al 7075-T7451 was developed to obtain milling force simulations. Finally, simulated results are compared with experimental data and are shown to be in good agreement with each other.

Introduction

Metal cutting process can be considered as a deformation process where deformation is highly concentrated in a small zone. Thus, cutting can be considered as a chip formation process and simulated using finite element method. The main advantage of such an approach is able to predict chip flow, cutting forces, tool temperature and stresses that result in various cutting conditions. However, material flow stress at high temperature and deformation rates are required to conduct such predictions. There are very few material flow stress data available for the deformation conditions that exist in machining. Those data are mainly obtained by using impact compression tests for various materials at the moderate deformation rates. However, because those data were difficult in measuring, chip formation mechanism hasn’t always been well understood.

Recently, the cutting simulation has focused on 2D orthogonal cutting process. However, most of practical cutting operations are 3D oblique cutting. In order to reveal the true cutting process, some researchers established the finite element model of 3D continuous cutting process [1-4]. However, the practical milling process is a discontinuous cutting and a very useful way to obtain industrial pieces. Therefore, the finite element model of a 3D milling process is established with the commercial finite analysis software of ABAQUS. The chip formation can be analyzed as well as the milling force. Model of cutting force

During the oblique cutting operation shown in Fig. 1, PAA′P′ is the shear plane denoted by Ps. b and h are the cutting width and the instantaneous undeformed cutting thickness, respectively. The normal shear angle φn is the included angle between Ps and x y -plane, i is the included angle between the resultant cutting force F and its projection on Pn, n is the included angle between the axis x and the projection of F on Pn, and the inclined shear angle φi is the included angle between the direction of shear speed and the intersection-line by Ps and Pn. In addition, γ is the incline angle between the cutting speed V and the cutting edge. Thus, the cutting force F can be obtained as [5]

F=τbhcos(

n+φn)cosicosφi+sin isinφi cosγ sinφ (1)

n

with τ is the shear stress.

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email