K9F1G08U0A_flash芯片手册
K9F1G08R0A
K9F1G08U0AK9K2G08U1A
Product Introduction
FLASH MEMORY
The K9F1G08X0A is a 1056Mbit(1,107,296,256 bit) memory organized as 65,536 rows(pages) by 2112x8 columns. Spare 64 col-umns are located from column address of 2048~2111. A 2112-byte data register and a 2112-byte cache register are serially con-nected to each other. Those serially connected registers are connected to memory cell arrays for accommodating data transferbetween the I/O buffers and memory cells during page read and page program operations. The memory array is made up of 32 cellsthat are serially connected to form a NAND structure. Each of the 32 cells resides in a different page. A block consists of two NANDstructured strings. A NAND structure consists of 32 cells. Total 1081344 NAND cells reside in a block. The program and read opera-tions are executed on a page basis, while the erase operation is executed on a block basis. The memory array consists of 1024 sep-arately erasable 128K-byte blocks. It indicates that the bit by bit erase operation is prohibited on the K9F1G08X0A.
The K9F1G08X0A has addresses multiplexed into 8 I/Os. This scheme dramatically reduces pin counts and allows system upgradesto future densities by maintaining consistency in system board design. Command, address and data are all written through I/O's bybringing WE to low while CE is low. Those are latched on the rising edge of WE. Command Latch Enable(CLE) and Address LatchEnable(ALE) are used to multiplex command and address respectively, via the I/O pins. Some commands require one bus cycle. Forexample, Reset Command, Status Read Command, etc require just one cycle bus. Some other commands, like page read and blockerase and page program, require two cycles: one cycle for setup and the other cycle for execution. The 128M byte physical spacerequires 28 addresses, thereby requiring four cycles for addressing: 2 cycles of column address, 2 cycles of row address, in thatorder. Page Read and Page Program need the same four address cycles following the required command input. In Block Erase oper-ation, however, only the two row address cycles are used. Device operations are selected by writing specific commands into the com-mand register. Table 1 defines the specific commands of the K9F1G08X0A.
The device provides cache program in a block. It is possible to write data into the cache registers while data stored in data registersare being programmed into memory cells in cache program mode. The program performace may be dramatically improved by cacheprogram when there are lots of pages of data to be programmed.
In addition to the enhanced architecture and interface, the device incorporates copy-back program feature from one page to anotherpage without need for transporting the data to and from the external buffer memory. Since the time-consuming serial access anddata-input cycles are removed, system performance for solid-state disk application is significantly increased.
Table 1. Command Sets
Function
Read for Copy BackRead IDResetPage ProgramCache Program*2Copy-Back ProgramBlock EraseRandom Data Input*1Random Data Output*1Read Status
1st. Cycle
00h90hFFh80h80h85h60h85h05h70h
2nd. Cycle
30h35h--10h15h10hD0h-E0h
OO
Acceptable Command during Busy
NOTE : 1. Random Data Input/Output can be executed in a page.
2. Cache program and Copy-Back program are supported only with 3.3V device.
Caution : Any undefined command inputs are prohibited except for above command set of Table 1.
A 400? 8mA 输入低电 平电压V 平电压ViL 输出高电平 电流I 电流IOH 输出低电 平电流 IOL Intel 8255A 是一个通用的可编程的并行接口芯片,它有三个并行 I...
怎样读芯片数据手册_信息与通信_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 怎样读芯片数据手册_信息与通信_工程科技_专业资料。讲授一些学习芯片的技巧...
K9F1G08U0A_flash芯片手册 37页 免费 基于FPGA的USB接口IP核设计... 6页 免费...1 主机控制器芯片, 并对该芯片进行软硬件协同验证。通 过内嵌 Pow PC和 U ...
芯片数据手册_信息与通信_工程科技_专业资料。ADSP-21368 芯片数据手册 及主要产品推荐 包括:ADSP-21367 ; ADSP-21369 ADSP-21371; ADSP-21375 2006 年第 1 版...
Ax5510芯片数据手册_电子/电路_工程科技_专业资料。升压芯片 可用于驱动LEDAX5510A 680K/1.2MHz, High Voltage, Boost Converter ? GENERAL DESCRIPTION The AX5510A...
如何阅读芯片数据手册_信息与通信_工程科技_专业资料。如何阅读芯片数据手册如何阅读数据手册 How the WIMS outreach program to Read a Datasheet Prepared for 5/6...
芯片应用手册n-al)_信息与通信_工程科技_专业资料。芯片应用手册n-al)晶能光电(江西)有限公司? Lattice?Power(Jiangxi)? Corporation? 芯片应用手册(Virgo200) 引...
74系列芯片数据手册大全_信息与通信_工程科技_专业资料。74系列芯片数据手册大全系列芯片数据手册大全【强烈推荐】 74 系列芯片数据手册大全【强烈推荐】 74 系列集成...
串行FLASH配置芯片(EPCS1或EPCS4)数据手册_信息与通信_工程科技_专业资料。串行FLASH配置芯片(EPCS1或EPCS4)数据手册Serial Configuration Devices (EPCS1 & EPCS4)...
SYN470R_SYN480R 数据手册_信息与通信_工程科技_专业资料。接收芯片 SYN480R SYN470RSYN470R Datasheet (300-450MHz ASK Receiver) Version 1.0 目录 1.总体介绍.....
热门文档