文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > epcs1
侵权投诉

epcs1

epcs1

C51014-2.0

Introduction

Functional Description

Altera Corporation April 2007

4.Serial ConfigurationDevices (EPCS1, EPCS4,EPCS16, & EPCS64) Features

The serial configuration devices provide the following features:

■

1-, 4-, 16-, and 64-Mbit flash memory devices that serially configure Stratix® II, Stratix® II GX, and Stratix® III FPGAs and the Cyclone® series FPGAs using the active serial (AS) configuration scheme■Easy-to-use four-pin interface

■Low cost, low pin count and non-volatile memory

■Low current during configuration and near-zero standby mode current

■3.3-V operation

■Available in 8-pin and 16-pin small outline integrated circuit (SOIC) package

■Enables the Nios® processor to access unused flash memory through AS memory interface

■Re-programmable memory with more than 100,000 erase/program cycles

■Write protection support for memory sectors using status register bits

■In-system programming support with SRunner software driver■In-system programming support with USB Blaster , EthernetBlaster , or ByteBlaster II download cables

■

Additional programming support with the Altera® Programming Unit (APU) and programming hardware from BP Microsystems, System General, and other vendors

■

Software design support with the Altera Quartus®II development system for Windows-based PCs as well as Sun SPARC station and HP9000 Series 700/800

■

Delivered with the memory array erased (all the bits set to 1)

1

Whenever the term “serial configuration device(s)” is used in this document, it refers to Altera EPCS1, EPCS4, EPCS16, and EPCS64 devices.

With SRAM-based devices that support active serial configuration,

configuration data must be reloaded each time the device powers up, the system reconfigures, or when new configuration data is needed. Serial configuration devices are flash memory devices with a serial interface

4–1

epcs1

第1页

你可能喜欢

热门文档

相关文档

  • EPCS1SI8;EPCS1SI8N;EPCS4SI8N;EPCS4SI8;EPCS16SI8N;中...

    For an 8-pin SOIC package, you can migrate vertically from the EPCS1 device to the EPCS4 or EPCS16 device. For a 16-pin SOIC package, you can ...

  • epcs1_and_epcs4

    5 2.9 ic e p pr 00-u SI8 1 1 EPCS 90 10. ic e p pr 00-u SI8 1 4 EPCS EPCS1 and EPCS4 Con?guration Devices from Altera? The ...

  • 串行FLASH配置芯片(EPCS1或EPCS4)数据手册

    Figure 1. Altera Serial Configuration Device Package Pin-Out Diagram EPCS1 or EPCS4 Device nCS DATA VCC GND 1 2 3 4 8 7 6 5 VCC VCC DCLK ASDI ...

  • EPCS1(008-SOIC)

    EPCS1(008-SOIC)芯片手册Altera Device Package Information 8-Pin Small Outline ...

  • EPCS编程实验

    (2)参照图 3.53 在 Configuration device 下拉框中根据实际设计选择被编程目标器件, 于 QuickSOPC 为 EPCS1; (3)参照图 3.53 在 File name 编辑框中, 输入...

  • EPCS FLASH容量解读

    结论: 结论:(一)对于 EP2C ,假设我们以上最基本的设计来计算容量,则 Verilog+NIOS II = 120KB+57KB=177KB>128KB 所以 EPCS1 不够用 因此, (1)若 Verilog...

  • 在NIOS II中读写EPCS剩余空间

    (注:只有 EPCS1 每个块 32768 字节,其余配置芯片是每块 65536 字节。) alt_epcs_flash_erase_block(my_epcs, regions->offset+0x70000);//擦除第 8 块 ...

  • 使用JTAG下载EPCS器件的方法

    图七:Generate 文件界面 顺便提醒一下, 不要忘记把 Configuration device 选为您所使用的 EPCS4 或者 EPCS1. 8. 以下的下载步骤与我们普通的 JTAG 下载过程基本...

  • 如何指定EPCS型号

    如何指定EPCS型号_信息与通信_工程科技_专业资料。如何指定 EPCS 型号 由于没有指定 EPCS 器件,编译后没有 POF 文件。下面是指定 EPCS 过程。 1 打开 Quartus...

  • Storm I_1C3_FPGA_V1.1 使用手册

    3. STORM I_FPGA 规格: 本实验板配置如下: 1、 1 片 EP1C3T144C8; 2、 1 个 JTAG 接口和 1 个 AS 接口; 3、 1 片 EPCS1; 4、 USB 接口提供电源;...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email