15thASCEEngineeringMechanicsConferenceJune2-5,2002,ColumbiaUniversity,NewYork,NY
EM
2002
DEM SIMULATIONS OF THE DIRECT SHEAR TEST
Ling Zhang1 and Colin Thornton1
ABSTRACT
DEM simulations of the direct shear test have been performed under both constant normal stress and constant volume conditions. Results are presented to show how the state of stress in the shear band evolves. Comparisons with boundary force calculations are made and implications for laboratory measurements are discussed. At the critical state, the results are also interpreted in terms of Mohr’s circles of stress and strain rate.
Keywords: Numerical simulation, direct shear, shear bands, critical state.
INTRODUCTION
In the direct shear test, the top half of the specimen is translated relative to the bottom half resulting in the formation of a shear band across the mid-height of the specimen. The applied vertical and horizontal forces are measured and the ratio of horizontal to vertical load is assumed to provide an estimate of the average ratio of shear to normal stress acting in the shear band; thus providing a direct measure of the ‘internal friction angle’. It is, however, unclear how reliable this traditional interpretation is since the exact state of stress within the shear band is unknown.
Numerical simulations of the direct shear test have been performed under both constant normal stress and constant volume conditions. Results are presented to show how the average stress ratio acting in the shear band compares with the force data at the boundaries. The principal directions of stress and strain-rate in the shear band are shown to be coaxial at the critical state. Using the corresponding Mohr’s circles, the interpretation of direct shear test data is discussed in the context of traditional experimental measurements.
SIMULATION PROCEDURES
With the Aston TRUBAL code, two-dimensional simulations of the direct shear test using the Discrete Element Method (DEM) have been performed on a polydisperse system of 5000 elastic spheres using seven different sizes varying from 30 µm to 90 µm with an average size of 60 µm. The mechanical properties of the particles are: Young’s modulus E = 8.34 GPa, Poisson’s ratio ν = 0.35 and surface friction coefficient µ = 0.5. The test arrangement is shown diagrammatically in Fig. 1. The upper half of the specimen is contained by four walls (AB, BC, CD and DE), which are all translated horizontally in the opposite direction to the four walls (FG, GH, HI and IJ) containing the lower half of the box. The top and bottom walls (CD and HI) are free to move vertically. In the simulations the walls do not interact with other walls, only with
state in the discrete element method (DEM) simulation of direct shear test...Simulations of unit vectors along plastic strain rates obtained from drained ...
The results of DEM simulations show that the process of tunnel face failure...the direct shear test height of the specimen in the direct shear test ...
strength increment due to root c = 20.7 kPa (see Table 7) was obtained from the simulations of the direct shear test on the Makino bamboo root ...
CFD–DEM models and numerical simulations were developed...uid convection, radiation, and direct conduction ...test the validity of the code in the extreme ...
Available online at www.sciencedirect.com ...The present work uses DEM simulations to ...of particle diffusive motion in a Couette shear ...
Development and test of CFD–DEM model for complex...Please note that Direct Numerical Simulation models...The model is limited to 2D simulations. In ...
DEM simulation of particle attrition in dilute-phase pneumatic conveying_能源/...To the best of our knowledge, the ?rst simulations that considered particle...
DIRECT NUMERICAL SIMULATIONS OF TURBULENT CHANNEL FLOWS WITH CONSIDERATION OF THE BUOYANCY EFFEC_专业资料。28 2 Avlbl~leataieai nwww.ce~sin一 ic.onrtr ec ...
various results from numerical simulations of biaxial...shear bands in biaxial test and in the passive ...in Kaolinite sample subjected to direct shear. The...
Discrete Element Method (DEM) used in the Simulations of Liquid-solid flow_自然科学_专业资料。有限离散元方法 DEM1 Discrete Element Method (DEM) used in...
DEM simulation of gas–solid flow behaviors in spout...Numerical simulations have become popular in the ?...(1) Direct numerical simulation (DNS), to ...
热门文档