飞机涡轮清洗程序
71-43-00(OriginalIssue)
TURBINEBLADEWASH-MAINTENANCEPRACTICES
1.General
A.
2.Turbinebladewashisaccomplishedtoremovedepositbuild-upaccumulatedonturbinebladesduringnormaloperation.
WashTurbineBlades(RefertoFigure201).
NOTE:RefertoPilot'sOperatingHandbookforstartermotorcyclelimitations.
NOTE:Aminimumcool-downperiodof40minutesshouldbeobservedafterenginerunningand
priortoinjectingrinsefluid.
NOTE:Compressorturbinebladewashingistobeaccomplishedusingwaterofdrinkingquality
(potable)onlyatambienttemperaturesof36°Fandabove,andapotablewater/methanol
solutionatambienttemperaturesbelow36°F.ConsultapplicableEngineMaintenance
Manualforsolutionstrengthsaccordingtoambienttemperature.
(1)
(2)Removeoneofthetwoigniterplugs.InstallspraytubeP/NPWC32271inigniterplugbossandtightenspraytubefingertight.
Ensurethatarrowontabofspraytubeisdirectedtowardenginereductiongearboxandis
parallelwithcenterlineofengine.TurbineBladeWashA.
CAUTION:Deliveryhoseshouldbesupportedsoastopreventdamagetothe
spraytube.
(3)
(4)Connectasuitablecleaningrighosetothespraytubeadapter.Water/solutionsupplydeliverypressureis40psi.Ensureengineignitionisoffandaircraftbleedairisshutoff.
CAUTION:Observestartermotorlimitations.
(5)Carryouta30secondmotoringcycle,introducingthewashsolutionwhenthecompressor
attainsaspeedofapproximately5%Ng.
NOTE:Approximatelyone-halfgallonofrinsesolutionwillbepassedthroughthe
compressorturbineduringa30secondcycle.
CAUTION:Whenusingawater/methanolsolution,performanadditional30
secondsdrymotoringcycleaftereachwashingcycletopurgeengineof
volatilefumes.Ensureprescribedstartercoolingperiodsareobserved.
(6)
(7)
(8)Repeatwashingcycleasrequiredtoremovecontaminantsfromturbineblades.Removespraytubeassemblyandreinstalligniterplug.Performtwoconsecutiveenginedrymotoringruns,ensuringthatstarterrunningtime
limitationsarenotexceeded.
©2011CessnaAircraftCompany
Retainprinteddataforhistoricalreferenceonly.Forfuturemaintenance,useonlycurrentdata.Page1
运行中发动机涡轮增压器的清洗方法_专业资料。在发动机热态和全负荷状态下可对涡轮增压器的压气机端进行湿洗,发动机在低负荷运转情况下对涡轮端进行湿洗或在发动机...
1财富值 外墙清洗程序 3页 免费 涡轮清洗程序 2页 5财富值 油烟机清洗程序1 4页 免费喜欢此文档的还喜欢 欧洲银器 1页 免费 银器发暗怎么办 2页 免费 ...
涡轮增压器再制造清洗工艺第二版_材料科学_工程科技_专业资料。涡轮增压器 再制造清洗工艺 Turbocharger Rebuilding Cleaning Process 涡轮增压器 实际上是一种空气...
清洗程序: 1. 如果涡轮前废气最高温度超过 430℃(703K),应降低柴油机负荷,戒如果 涡轮前废气温度低于 300℃(573K),增加柴油机负荷。 2. 在开始喷水前,应等...
涡轮流量计安装、维护、清洗一、 流量计安装方式 涡轮流量计安装要求(只能采取水平安装方式) - 流量计前端安装有效的过滤装置; 流量计前后应具有相关要求的直管段...
10.用塑壳清洁剂将拆取下来的上盖,下盖,涡轮进行冲洗。 11.安装拆下来的涡轮以及上盖和下盖 12.验机,并与清洗前各项功能进行对比,如有异常,及时分析原因并...
涡轮增压器 再制造清洗工艺 Turbocharger Rebuilding Cleaning Process 涡轮增压器 实际上是一种空气压缩机,通过压缩空气来增加进 气量。它是利用发动机排出的废气惯性...
15、将斯黛乐消毒药水按比例稀释装入喷雾器中,对表冷器、风机叶轮及涡轮、冷凝...落地柜,吊柜,风机盘管清洗完后,表冷器、叶轮一定要进行杀毒程序,杀菌剂要求安...
中机匣排放阀,每一清洗喷射循环大约 5升(1.09 加仑) ?高压涡轮机匣排放阀,...过程 (1) 在开始开车状态清洗维修程序之前,必须保证燃气发生器被彻底清 洁,尽...
称为油污染, 被污染后涡轮分子泵的叶片就必须在厂家的指导 下用氟利昂来清洗。...5、操作程序 由于涡轮分子泵的种类和型号是多种多样的, 每种泵的操作方 式由...
热门文档