数学模型 轴承
Peqpnnon
OBJECT-BRIDLED MATHEMATICAL MUDELLIN~APPLIED TO MACHINE ELEMENTS D. FRITZSON,~ P. FRITZSON,~ L. VIKLUND$ and$%I? Engineering ResearchCentre B-V., P.O. Box 2350, 3430 DT&
J. HERBERT Niuwegein, The Netherlands
$Department of Computer and~nfo~at~on Science, Linkaping University. S-F&f 83 Linkciping, Sweden (Received 21 December 1992)
Ahatmact-Machine element analysis has a goal of describing function and other aspects of machine elements in a theoretical form. This paper shows how ideas from object-oriented modelling can be applied to machine element analysis. The models thus obtained are both easier to understand, better structured, and allow a higher degree of re-use than conventional mode&. An obj~t~~~t~ model axon is natural and suitable for machine element analysis. As a reahstic example an equational model of rolling bearings is presented. The structure of the model is general, and applies to many types of rolling bearings. The model and ane solution require approximately 200+ 200 equations. The model is extensible, e.g. simple submodels of detailed properties can be made more complex without altering the overall structure. The example model has been implemented in a language of our own design, ObjectMath@Object-oriented Mathematical ianguage for scientific computing). Using ObjectMath, it is possible to model classes of equation objects, to support mu&pie and single inheritance of equations, to support composition of equations, and to soIve systems of equations. Algebraic transformations can~nveni~tly be done since Obj~tMath models are translated into the Mathematics computer algebra language. When necessary, equations can be transformed to C++ code for efficient numerical solution. The m-use of equatians through inheritance. reduced the size of the model by a factor of two, compared to a direct representation of the model in the Mathematics computer algebra language.
1. INTRODUCTION we focus on how to improve the machine elements, by in~~uci~~ methods and tools that provide better and&arer model structure, and enhanced t-e-usability. We In this paper modeiing of
2. MOTWAITON
investigate the use of object-oriented modelling teohniques for machine element modelling. The investigated modelling technique supports programming in equations instead of low-level procedural programming and permits better reuse of equations in mathematical modeis. Some questions are: How will an object-oriented description compare to and support a‘natural’ description of machine elements? Will it support the‘thought process’ of a mechanical analyst? * Will it simplify the model definition and simulation phases? l
To evaluate the technique, a prototype of a mechan&al analyst’s workbench, including a modelllng language, ObjectMath (Object-oriented Mathematical language for ScientiIIc comptning), has been designed and implemented, and used for a rather realistic rolling bearing application. ObjectMath was developed through the coopera
tion between application experts and computer scientists. 241
The current state of the art in modelling and propping in mechanical analysis is still very lowlevel. We will illustrate some main points in this paper. It has been discussed in more detail in[1,2]. There are two main classes of activities within research projects or advanced development projects in mechanical analysis of machine elements: theory development and numerical computation. During theory development, a mathema~c~ model is developed that describes the relevant properties of the investigated machine element. This is normally done manually, using only pen and paper. In order to perform numerical computations, the model must be translated to some programming language, or to input specifications for some existing numerical modelling program, e.g. a finite element analysis systems analysis program, program, multibody matrix languages, differential equation solving system, etc. A detailed review of the currently available tools, their strengths and weaknesses induding full references and discussion can be found in[l, 21. Normally, existing high-level tools can at best be used for limited parts of the total computational problem, because it is usually too complex and does not fit to the available tools or analysis programs. Therefore, a designer often spends more than half the

























Image-Based 3D Modelling_A review_2006_互联网_IT...object information through a mathematical model or ...further matching procedures are applied in order to...
Cole, Mathematical and Numerical Modelling of ...nite elements for simulation of T-gate MESFETs ...equations applied to semiconductor device modelling....
Applied Mathematical Modelling ,2010,34:8-21. 今日推荐 180份文档 CET四六级高分通关宝典 2014年6月大学英语六级考试真题及答案 2014年12月大学四级冲刺试题及...
The purpose of the modelling approach employed in this work was to classify...ANN modeling and several mathematical models were applied to predict the ...
approach to obtain mathematical model of a ...The inaccuracies in FEM, when applied to dynamic...In study 1, the finite element modelling has ...
Applied Physics, Department of Metals Extraction ...population balance model Mathematical modelling allows...3. Tundish and industrial experiment The object ...
(1995) 265-280 [41 Modelling overland flow with...A time-dependent mathematical submodel was developed...q’ is the applied external boundary flux; VWis...
Mathematical Modelling 0307904X Applied Mathematics ...Object Retrieval, EG 3DOR 19970463 Eurographics ...Oriented Systems 21567921 2156793X ICSE Workshop on...
APPLIED MATHEMATICAL MODELLING JOURNAL OF WIND ENGINEERING AND INDUSTRIAL AERO...ELEMENTS IN ANALYSIS AND DESIGN 0.274 0.262 0.250 0.241 0.241 0.228...
Modelling Physical, mathematical , computational , ...Can be applied to geometrical identities (points,...3D object representation ? – Wire-frames – ...
热门文档