热镀锌退火温度对DP780组织和性能的影响
陈杰 唐荻 赵征志 江海涛
(北京科技大学 冶金工程研究院 北京 100083)
摘 要: 主要研究了热镀锌退火温度对DP780的组织和性能的影响。利用OM、SEM、TEM等技术对显微
组织进行了观察和分析,并结合性能进行了研究。实验结果表明:随退火温度升高,抗拉强度呈稳定或降低趋势,主要是因为奥氏体的淬透性降低,产生了非马氏体组织,导致马氏体的复相强化作用降低。受非马氏体组织的影响,可动位错密度降低的作用,屈服强度、屈强比随退火温度升高而升高。总体来说,在780-800℃之间退火,细小弥散的马氏体均匀分布在铁素体中,这种组织的钢综合性能良好。 关键词:双相钢;热镀锌;显微组织;非马氏体组织
Effect of hot-dip galvanization temperature on Microstructure
and Mechanical Properties of DP780
Chen Jie Tang Di Zhao Zhengzhi Jiang Haitao
(Research Institute of Metallurgy Engineering , University of Science and Technology Beijing ,
Beijing 100083 ,China)
Abstract: The effects of hot-dip galvanizing annealing temperature on microstructure and mechanical properties of DP780 were investigated in this paper. The microstructure was observed and analyzed by OM, SEM and TEM techniques. The results indicated that the tensile strength hardly change or decrease with the annealing temperature, which may be due to the decrease of martensite’s multiphase reinforcement because the emergence of non-martensite for austensite’s hardenability decrease. Yield strength, yield ratio increase with the increase of annealing temperature, due to the impact of non-martensite and decrease of movable dislocation density. In general, this microstructure that fine dispersed martensite distribute in the ferrite can be obtained with a annealing temperature from 780 to 800℃, and this DP steel presents a good comprehensive properties. Key words: dual phase steel; hot-dip galvanizing; microstructure; non-martensite
1 前言
减轻汽车自重引发了对高强度钢开发的热潮,如今先进高强度钢板已形成不同强度级别的品种系列,主要包括:双相钢(DP)、复相钢(CP)、相变诱导塑性钢(TRIP)、孪晶诱导塑性钢(TWIP)、低碳马氏体钢[1]

。双相钢由铁素体与马氏体组成,马氏体为强化相,
2009 冷轧热镀锌双相钢 DP780 的组织与性能实验研究鲍成人1 , 李 众1 , ...而其它生产工序的工艺变化影响很 小 ,所以研究的重点放在 C GL 上[ 1 ] 。...
2.学位论文 陈杰 冷轧DP钢热镀锌工艺及微合金化机理研究 2009 本课题结合实际生产条件,主要研究退火工艺参数对冷轧双相组织性能 的影响,为实际生产提供参考依据,并...
奥氏体化时间对DP780冷轧双相钢组织和性能的影响_自然科学_专业资料。个人...():35 程东妹 , 都晓东 , 俞铜强. 双相钢热 镀锌工艺 现状 . 轧钢 ,07...
A ? ? 0412?1961(2013)02?0159?08 EFFECT OF STRAIN RATE ON DYNAMIC DEFORMATION BEHAVIOR OF DP780 STEEL DONG Danyang 1) , LIU Yang 2) , WANG Lei...
连续镀锌DP600双相钢的组织与性能研究_专业资料。制备了连续镀锌DP600双相钢,利用光学显微镜、SEM、EBSD技术对其显微组织进行了观察和分析;利用X射线衍射和EBSD...
热镀锌TRIP钢中马氏体对... 暂无评价 5页 免费 汽车用DP钢与TRIP钢的成....摘 要 研究了热镀锌用高强 TR IP钢的退火工艺对性能的影响和组织演变规律 . ...
??? A ? ?? 0412?1961(2013)12?1493?08 EFFECT OF STRAIN RATE ON DYNAMIC DEFORMATION BEHAVIOR OF LASER WELDED DP780 STEEL JOINTS DONG Danyang 1) ,...
藉 SEM , 分析了试样颈缩区的变形 组织和断口 ...SSAB 公司提供的厚度 2 0m m 的热 镀锌 DP 钢...性能 的影响, 认为纳米镍拉伸试样尺寸对拉伸性能影响...
热镀锌双相钢DP590、DP780、DP980和热浸镀锌双相钢DP600、 2 DP780 [8]...1.3 影响双相钢组织和力学性能的因素 1.3.1 合金元素的影响[24]7 如图 ...
冷轧热镀锌双相钢DP780的... 暂无评价 5页 2...热镀锌双相钢主要合金成分对产品力学性能的影响进行...在微观组织上 , 双相钢是由较软的铁素 体加 10...
热门文档