ublox 软件编程手册

Supported SBAS messages continuedMessage TypeMessage ContentSource
24
25
26Mixed Fast / Long term CorrectionsLong term Corrections

Ionosphere DelaysPrimary

PrimaryPrimary
Each satellite services a specific region and its correction signal is only useful within that region. Planning iscrucial to determine the best possible configuration, especially in areas where signals from different SBASsystems can be received:
Example 1: SBAS Receiver in North America
In the eastern parts of North America, be careful that EGNOS satellites do not take preference over WAASsatellites, the satellites from the EGNOS system should be disallowed using the PRN Mask.
Example 2: SBAS Receiver in Europe
Some WAAS satellites can be received in the western parts of Europe, therefore it is recommended that thesatellites from all but the EGNOS system should be disallowed using the PRN Mask.
Although u-blox receivers try to select the best available SBAS correction data, it is recommended
to configure them to disallow using unwanted SBAS satellites.
The EGNOS SBAS system does not provide the satellite ranging function.
5.3 SBAS Configuration
To configure the SBAS functionalities use the UBX proprietary message UBX-CFG-SBAS (SBAS Configuration).SBAS Configuration parametersParameterDescription
Mode - SBAS Subsystem
Mode - Allow test mode usage
Services/Usage - Ranging
Services/Usage - Apply SBAS
correction data
Services/Usage - Apply integrity
information
Number of tracking channels
PRN MaskEnables or disables the SBAS subsystemAllow / Disallow SBAS usage from satellites in Test Mode (Message 0)Use the SBAS satellites for navigationCombined enable/disable switch for Fast-, Long-Term and IonosphereCorrectionsUse integrity dataShould be set using UBX-CGF-GNSS. The field in UBX-CFG-SBAS isno longer supported.Allows selectively enabling/disabling SBAS satellites (e.g. restrict SBAS
usage to WAAS-only).
By default SBAS is enabled with three prioritized SBAS channels and it will use any received SBAS satellites(except for those in test mode) for navigation, ionosphere parameters and corrections.
6 Clocks and Time
6.1 Receiver Local Time
The receiver is dependent on a local oscillator (normally a TCXO or Crystal oscillator) for both the operation ofits radio parts and also for timing within its signal processing. No matter what the nominal frequency the localoscillator is (e.g. 26MHz), u-blox receivers subdivide the oscillator signal to provide a 1kHz reference clock
signal which is used to drive many of the receiver's processes. In particular the measurement of satellite signals
135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...
Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...
4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...
Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...
(串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...
(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...
PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...
PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...
‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...
Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...
热门文档