电池反接保护电路---TI应用文档
Application Report SLVA139 - June 2003
Reverse Current/Battery Protection Circuits Jeff Falin ABSTRACT Users of battery powered equipment expect safeguards to prevent damage to the internal electronics in the event of reverse battery installation, accidental short circuiting, or other inappropriate operation. These safeguards can be either mechanical or electronic. An example of a mechanical safeguard is requiring the use of special connectors and instructional pictures and symbols. For example, a 9-V battery has different terminals, and its rechargeable battery packs are physically designed for one direction of insertion. Other battery types, like single-cell alkaline, are not so easily protected by mechanical safeguards. Therefore, battery powered equipment designers and manufacturers must ensure that any reverse current flow and reverse bias voltage is low enough to prevent damage to either the battery itself or the equipment’s internal electronics. To provide these electronic safeguards, manufacturers typically chose either a diode or transistor for reverse battery protection. PMP Portable Power
Using a Diode The simplest protection against reverse battery protection is a diode in series with the battery, as seen in Figure 1.
VBAT
+–
LOAD –
Figure 1. Diode in Series With Battery In Figure 1, the diode becomes forward biased and the load’s normal operating current flows through the diode. When the battery is installed backwards, the diode reverse–biases and no current flows. This approach is used for any battery type, from single-cell alkaline to multiple Li-Ion, but it has two major disadvantages. The forward voltage drop across the diode shortens the usable battery life, i.e., a dual alkaline battery pack capable of providing 1.8 V, is limited to 1.8 V– 0.6 V= 1.2 V. In addition, the efficiency of the power circuitry (e.g., a boost converter) following the battery suffers due to this drop. To minimize these disadvantages, many designers use a Schottky diode, since its forward drop is lower than that of a regular diode. However, the disadvantage of using a Schottky diode is that it is more expensive than a standard diode.
Trademarks are the property of their respective owners. 1

电池反接保护电路 3页 1财富值 电池保护电路 2页 1财富值 浅谈笔记本电脑电池的保护... 4页 2财富值 两款镍镉电池的保护电路 2页 1财富值 电池保护电路...
在DS2726典型应用电路的基础上,通过简单设计修改,可利用DS2726 Li+电池保护器承受负压,在充电器反接时为电池提供保护。 关键词:充电器;反接;DS2726;U+电池保护...
3页 1下载券 电池保护电路工作原理知... 2页 免费喜欢此文档的还喜欢...LED 上负下正点亮提 示反接 3,N 管里的体二极管不会影响电路工作,电流只能...
DS2726在充电器反接时保护... 4页 免费 光伏系统中蓄电池的充电保... 6... 绍锂 离子 电池保 护 电路 :介 过度 充电保 护、电, 4路保 护和 过放...
防反接锂电池充电器电路图_电子/电路_工程科技_专业资料。cdq1.1.sch-1 -... 锂电池充电器电路图 2页 免费 锂电池保护板 8页 免费 LN2054_C中文版 10...
TP4055 500ma防反接保护_电子/电路_工程科技_专业资料。TP4055实际充电电流...当电池达到 4.2V 之后,充电电流降至设定值 1/10,TP4055 将自动终止充电。 ...
高精度单节锂电池充放电保护电路的设计_电子/电路_工程科技_专业资料。华中...充电器反接保护 元件 功率 NMOS 功率 NMOS 电阻 电容 电阻 应用电路中,R1 ...
锂电池保护电路 一般用户接触到手机锂离子电池,在...良反 应,影响电池性能.而这个电压的锂离子电池也...4.不要逆接电池正负极进行充电,同样会损伤保护 IC...
蓄电池过放电保护电路_电子/电路_工程科技_专业资料。蓄电池过放电保护电路上网...电路给负载供电,此后会重复“断开一接通一断开一接 通”的振荡过程,直到电池...
以下介绍此款锂电池保护 IC 的附加功能, 包括充电异常检测功能, 零伏电池充电禁止功能。 如图 4 所示。 图 4 附加功能电路结构 当锂电池接上充电器进行充电时...
热门文档