Abstract
With the rapid development of railways and other industries, the demand for more and more of aluminum, aluminum alloy welding quality requirements are also increasing. Aluminum welding technology, materials, and joint strength of the "Eighth Five-Year" period was listed as a national research project.Many methods for welding aluminum, but for thick plate welding, MIG welding unique advantage: The device is simple, deep penetration, high welding efficiency, welding quality, welding good accessibility, adaptability, on the long, welding seam curve can be short and easy to implement well the advantages of automation.
The 5052 selection of the base metal alloy design, material selection Ф1.6mm of ER5356 welding wire to wire the different energy input, select three groups of process parameters on the 300 × 150 × 6mm of the base metal for MIG welding, welded joints by tensile , bending, impact, hardness, micro-cutting and other conventional mechanical test and microstructure analysis.
In this process, the joint strength of 82.5% in the base metal, there is softening of welded joints, HV value of 56 or so, the HV65 hardness around the weld, the hardness is lower than the weld softening zone, the joint toughness is good, is bending and reverse bending has reached 180 °. Tensile test, fracture location are in the softening zone near the fracture surface dull gray with obvious necking, ductile fracture.The lowest impact energy weld, heat affected zone followed. Micro-indentation shear tests rate as close to the weld to the base material, and gradually decreased. Weld microstructure is mainly α (Al) + β (Mg2 Al3) Lord, and coarse grains, stomata more than other areas, and large. The results show that for 5052 aluminum alloy welding, MIG welding process using optimized, relatively good performance of welded joints.
key words: Aluminum;MIG welding;Welded joints;Process Test
研究了双脉冲和单脉冲MIG焊对5052Al-Mg合金焊...
此外, 还通过微型剪切试验研究了接头的微区力学性能, 这 也为铝合金焊接接头力学性能的评定提供了一个简单、 快速且有效的方法。 双脉冲 MIG 焊; 5052 铝合金;...
5052 铝合金平板对接 MIG 焊工艺设计学 生:和谐 指导老师:和谐 (三峡大学 机械与材料学院) 摘要:本说明书分析了 5052 铝合金的化学成分、力学性能和它的焊接性...
双脉冲MIG焊对5052铝合金... 5页 免费 铝合金激光-MIG复合焊焊... 21页 ...Zhang 等人研究了 6061 铝合金双丝焊接接头微观组织与性能 . 为此, 文中开展了...
针对10mm厚的5052铝合金采用激光一MIG复合焊接技术进行焊接.利用光学显微镜、扫描电镜和维氏硬度计等t具对 焊接接头组织、元素分布和力学性能等进行研究,结果表明:...
5052铝合金CO_2激光-MIG... 暂无评价 5页 2.00 铝镁合金管道焊接工艺卡...材及焊材 的清理工作以及采取恰当的反变形措施,从而保证获得良好的焊接接头性能。...
本文对铝 合金板材的 MIG 焊进行了工艺实验与分析,以便 按所确定的焊接规范来...焊接接头力学性能测试结果如表 3,可见其接 头强度低于原始母材的强度, 试样均...
铝合金TIG和MIG焊接工艺简介_材料科学_工程科技_专业资料。铝合金TIG和MIG 焊接...铝合金材料特点 3.铝合金材料牌号举例 5052H34,H34表示加工硬化,1/2硬状态。...
焊接工艺对2024铝合金接头组织与性能的影响_专业资料。研究了分别采用熔化极氩弧焊...这是由于MIG焊接头焊缝组织要比ⅡG焊接头焊缝组织细小,晶界;处共晶相数量明显...
热门文档