文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > TAP304_2008-10
侵权投诉

TAP304_2008-10

挪威船级社规范---钢制锻件产品型式认可规范

FOREWORD

DET NORSKE VERITAS (DNV) is an autonomous and independent foundation with the objectives of safeguarding life, prop-erty and the environment, at sea and onshore. DNV undertakes classification, certification, and other verification and consultancyservices relating to quality of ships, offshore units and installations, and onshore industries worldwide, and carries out researchin relation to these functions.

Standards for Certification

Standards for Certification (previously Certification Notes) are publications that contain principles, acceptance criteria and prac-tical information related to the Society's consideration of objects, personnel, organisations, services and operations. Standardsfor Certification also apply as the basis for the issue of certificates and/or declarations that may not necessarily be related to clas-sification.

A list of Standards for Certification is found in the latest edition of Pt.0 Ch.1 of the ”Rules for Classification of Ships” and the”Rules for Classification of High Speed, Light Craft and Naval Surface Craft”.

The list of Standards for Certification is also included in the current “Classification Services – Publications” issued by the Soci-ety, which is available on request. All publications may be ordered from the Society’s Web site doc.guandang.net Society reserves the exclusive right to interpret, decide equivalence or make exemptions to this Standard for Certification.

Main changes

Approval Programme No. 304 dated July 1999 has been rewritten, and the main changes are:—steel types for approval are divided in 7 groups

—additional test requirements for Continuous Grain Flow (CGF) crankshafts, Specially approved forging process, Clean steel

forgings, and steel forgings for low temperature service have been specified—steelmaking part has been removed (will now enter into 301A).

Comments may be sent by e-mail to rules@dnv.com

© Det Norske Veritas

Computer Typesetting (FM+SGML) by Det Norske Veritas

If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such personfor his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compen-sation shall never exceed USD 2 million.

In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of DetNorske Veritas.

上一页第2页

你可能喜欢

热门文档

相关文档

  • AISTech 2008 - FastArc technology P7-10

    AISTech 2008 - FastArc technology P7-10_冶金/矿山/地质_工程科技_专业资料...Tap to Tap 1630 (°C) Tapping Temperature Single Bucket Charge 0.7-0.8...

  • gb21671-2008测试步骤

    gb21671-2008测试步骤_计算机软件及应用_IT/计算机_专业资料。第三部分 测试... 将需要测试的网络的汇聚层至核心层交换机链路用 tap 或镜像的方式接入 ES ...

  • 多媒体技术08-09-2试卷-09040051-A

    Premiere 中,关于 Multitap Delay 音频滤镜的描述,以下___是正确的。 A.该滤镜定义整个音频素材的整个声音的质量 B.该滤镜放大音频素材的低音部分,但是使得其他...

  • FS36-350;中文规格书,Datasheet资料

    The output voltage will be either 36.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • 预应力技术2008-3

    预应力技术2008-3_建筑/土木_工程科技_专业资料。预应力技术MCG.x.Tzj9Ok^ij...Y A}E:~pr3L8pg8/:~pgh.o r9KvzP7+8/J8cw02r*tAP 7Zth4we_8SS-E+SNLY^...

  • Zeta_Training_sc

    ACE_2008_SC_training(6... 48页 1下载券 SC...(tap water) Na4P2O7 Colloid:100ppm Minusil 10 ... k-1 = 0.304/(I)0.5 (nm) 计算离子强度 ...

  • FS20-120;中文规格书,Datasheet资料

    The output voltage will be either 20.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

  • 2008WINAPN USB KEY客户端使用说明书V3.01

    2008WINAPN USB KEY客户端使用说明书V3.01_IT/计算机_专业资料。2008WINAPN ...“本地连接”的属性,如图所示 (TAP-Win32 Adapter V8) , 增加了一个“...

  • FS24-250;中文规格书,Datasheet资料

    The output voltage will be either 24.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • FS28-040;中文规格书,Datasheet资料

    The output voltage will be either 28.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email