7.REFERENCES
[1]JOHNSON, JeffreyH., “Power Amplifiers andThe Loudspeaker Load: Some Problems and a FewSuggestions,” Audio, August, 1977.
[2]BENJAMIN, Eric, “Audio Power Amplifiers forLoudspeaker Loads,” Journal of The AudioEngineering Society, Vol. 42, No. 9, September,1994.
[3]OTALA, Matti and HUTTUNEN, Pertti, “PeakCurrent Requirement of Commercial LoudspeakerSystems,” Journal of The Audio Engineering Society, Vol. 35, No. 6, June, 1987.[4]MARTIKAINEN, Ilpo and VARLA, Ari,“About Loudspeaker System Impedance WithTransient Drive,” AudioEngineering Society 71stConvention, Montreux, March 2-5, 1982.
[5]BORTONI, Rosalfonso, FILHO, Sidnei Nocetiand SEARA, Rui. "On The Design and Efficiency ofClass A, B, AB, G and H Audio Power AmplifierOutput Stages". Journal of The Audio EngineeringSociety, Vol. 50, No. 7/8, pp. 547-563, 2002July/August.
[6]WRIGHT, J. R. "An Empirical Model forLoudspeaker Motor Impedance". Journal of TheAudio Engineering Society, Vol. 38, No. 10, pp. 749-754, 1990 October.
[7]THIELE, A. Neville. "Loudspeakers in VentedBoxes: Parts I and II". Journal of The AudioEngineering Society, Vol. 19, No. 5, pp. 382-392,1971 May; and Vol. 19, No. 6, pp. 471-483, 1971June.
[8]SMALL, Richard H. "Direct-RadiatorLoudspeaker System Analysis". Journal of The Audio Engineering Society, Vol. 20, No. 5, pp. 383-395,1972 June.
[9]SMALL, Richard H. "Closed-Box LoudspeakerSystems– Part I: Analysis, and Part II: Synthesis".Journal of The Audio Engineering Society, Vol. 20,No. 10, pp. 798-808, 1972 December; and Vol. 21,No. 1, pp. 11-18, 1973 January.
[10]SMALL, Richard H. "Vented-Box LoudspeakerSystems– Part I: Small-Signal Analysis, Part I:Large-Signal Analysis, Part III: Synthesis, and PartIV: Appendices". Journal of The Audio EngineeringSociety, Vol. 21, No. 5, pp. 363-372, 1973 June; Vol. 21, No. 6, pp. 438-444, 1973 July; Vol. 21, No. 7, pp. 549-554, 1973 September; and Vol. 21, No. 8, pp.635-639, 1973 October.
[11]SILVA, Homero Sette, Analysis and Synthesis of Loudspeakers & Enclosures by Thiele-Small Method(in Portuguese), H. Sheldon Serviços deMarketingLtda., Rio de Janeiro, Brazil, 1996.
Figure 43. 2nd order Three Way Crossover load (Figure 28).
6.DISCUSSIONS AND CONCLUSIONS
Electrical models(equivalent circuits) of driversinstalled in infinite baffle,closed box,bass reflexenclosures,and4th and 6th order bandpasscabinets,and two and three way passive crossovers networksof1st and 2ndorders, had been presented.Using theparameters presented in manufacture’s data sheets,and the equivalent circuits of the acoustical cabinetsalong with the cross over networks,one got, fromsimulation, the impedance curves corresponding toeach case.New box models are obtainableintroducing the new parts into the models discussed.The efforts from the complex loads, to the poweramplifier outputstagesare shown in the current xvoltage graphics, so called load lines.
AES 115TH CONVENTION, NEW YORK, NEW YORK, 2003 OCTOBER 10-13

热门文档