汽车起重机伸缩臂系统设计论文
汽车起重机伸缩臂系统设计
学 生:肖文涛 指导老师:谭宗柒 三峡大学机械与材料学院
摘 要:臂架是起重机的主要承载构件。起重机通过臂架直接吊载,实现大的作业高度与幅度。臂架的强度决定了最大起重量时整机起重性能,其自重直接影响整机倾覆稳定性,因而臂架结构设计的优劣,将直接影响整机的性能,如整机重量、整机重心高度和整机稳定性等。所以要在保证臂架安全工作的条件下尽量减轻臂架的重量,这对提高整机质量和经济性具有很大的现实意义。本文主要根据QAY50吨汽车起重机工作要求来确定伸缩机构的结构和传动方案,进而采用传统的设计方法对主臂的三铰点、主臂的长度、及每节臂的长度、臂架的结构、液压缸尺寸进行确定,对臂架进行受力分析,利用有限元对臂架进行分析。
关键词:伸缩臂;液压缸;臂架结构,有限元分析
Design of truck crane Telescopic boom system
Student:Xiao Wen-tao Supervisor:Tan Zhong-qi
(College of Mechanical & Material Engineering, China Three Gorges University)
Abstract:Boom is the main host of crane components. Directly through the jib crane hanging load, to achieve great height and range operations. Arm strength determines the maximum time from the weight lifting machine performance, its weight directly affect the machine overturning stability, structural design and therefore merits of boom, will directly affect the overall performance, such as the weight of the whole machine center of gravity height and machine stability. Thus, to ensure safe working conditions of boom to minimize the weight of boom, which improves overall quality and economy of great practical significance. Mainly based on XCMG truck crane 50 tons of requests to determine the structure and transmission expansion program, and then using the traditional design method is the main arm of the three nodes, the main arm length, arm length, and each section, Boom structure, determine the size of hydraulic cylinders.
Keywords:Telescopic boom; hydraulic cylinder; Structure of boom ;ansys
汽车起重机伸缩臂交互可视化设计_专业资料。介绍了基于VisualC++语言的交互式伸缩臂设计程序。该程序实现了参数驱动的臂架外形图和警面图显示、人机交互的设计过程参...
机械毕业设计1224汽车起重机伸缩臂系统设计_工学_高等教育_教育专区。毕业设计(论文) 题目 汽车起重机伸缩臂系统设计 目录 前言……… 1 摘要……… 2 1 绪论 ...
汽车起重机伸缩臂用钢丝绳的设计和制造_专业资料。汽车起重机普遍采用伸缩油缸加绳排的伸缩结构,伸缩结构的最末一、二节采用钢丝绳,要求该钢丝绳破断拉力高、结构伸...
基于APDL的汽车起重机伸缩臂参数化设计_专业资料。针对汽车起重机伸缩臂设计过程中随着臂长和起重量的变化设计繁琐的缺点,采用有限元分析软件ANSYS的参数化设计语言(AP...
通过分析随车起重机工作时各节伸缩臂所受最大应力,应用等应力设计原理,确定了各节伸缩臂最佳伸缩量;对各节伸缩臂伸缩量控制系统进行了设计,并对控制系统的控制器...
基于ANSYS的汽车起重机伸缩臂滑块结构的优化设计_机械/仪表_工程科技_专业资料。第2 5卷第1 期 2014年1 月 文章 编号 :1674—1730(2014)01-0032-04 陇东学院...
伸缩臂是汽车起重机的主要受力构件,其重量约占整机的20%~30%,伸缩臂性能对大吨位起重机的大幅度和高起升高度工况的影响比较大。因此,通过优化设计增大起重量、降...
汽车起重机液压系统设计(毕业论文)_机械/仪表_工程科技_专业资料。纪念2011年毕业...有 2~4 节,最下(最外)一节为基本臂,吊臂内装有液压伸缩机构控制其伸缩。...
10 第二章 汽车起重机吊臂伸缩同步系统的总体设计方案... 11 2.1.1 伸缩臂...50 II 液压控制系统结业论文 第一章 绪论 1.1 研究的目的和意义 汽车起重机...
伸缩臂叉车安全控制系统设计_交通运输_工程科技_专业资料 暂无评价
热门文档