文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > linux内核自解压分析
侵权投诉

linux内核自解压分析

在嵌入式中一般使用压缩内核,所以在bootloader把压缩的内核移到SDRAM中时,先进行自解压
解压以后在调用arch/arm/kernel/head.S,而内核zImage的生成:先生成Image,然后经由gunzip压缩
成piggy.gz,然后和vmlinux.ld.S和head.S链接成zImage

#include <linux/linkage.h>

/*
* Debugging stuff
*
* Note that these macros must not contain any code which is not
* 100% relocatable. Any attempt to do so will result in a crash.
* Please select one of the following when turning on debugging.
*/
#ifdef DEBUG

#if defined(CONFIG_DEBUG_ICEDCC)

#ifdef CONFIG_CPU_V6
.macro loadsp, rb
.endm
.macro writeb, ch, rb
mcr p14, 0, \ch, c0, c5, 0
.endm
#elif defined(CONFIG_CPU_XSCALE)
.macro loadsp, rb
.endm
.macro writeb, ch, rb
mcr p14, 0, \ch, c8, c0, 0
.endm
#else
.macro loadsp, rb
.endm
.macro writeb, ch, rb
mcr p14, 0, \ch, c1, c0, 0
.endm
#endif

#else /* CONFIG_DEBUG_ICEDCC */

#include <mach/debug-macro.S>

.macro writeb, ch, rb
senduart \ch, \rb
.endm

#if defined(CONFIG_ARCH_SA1100)
.macro loadsp, rb
mov \rb, #0x80000000 @ physical base address
#ifdef CONFIG_DEBUG_LL_SER3
add \rb, \rb, #0x00050000 @ Ser3
#else
add \rb, \rb, #0x00010000 @ Ser1
#endif
.endm
#elif defined(CONFIG_ARCH_S3C2410)
.macro loadsp, rb
mov \rb, #0x50000000
add \rb, \rb, #0x4000 * CONFIG_S3C_LOWLEVEL_UART_PORT
.endm
#else
.macro loadsp, rb
addruart \rb
.endm
#endif
#endif
#endif

.macro kputc,val
mov r0, \val
bl putc
.endm

.macro kphex,val,len
mov r0, \val
mov r1, #\len
bl phex
.endm

.macro debug_reloc_start
#ifdef DEBUG
kputc #'\n'
kphex r6, 8 /* processor id */
kputc #':'
kphex r7, 8 /* architecture id */
#ifdef CONFIG_CPU_CP15
kputc #':'
mrc p15, 0, r0, c1, c0
kphex r0, 8 /* control reg */
#endif
kputc #'\n'
kphex r5, 8 /* decompressed kernel start */
kputc #'-'
kphex r9, 8 /* decompressed kernel end */
kputc #'>'
kphex r4, 8 /* kernel execution address */
kputc #'\n'
#endif
.endm

.macro debug_reloc_end
#ifdef DEBUG
kphex r5, 8 /* end of kernel */
kputc #'\n'
mov r0, r4
bl memdump /* dump 256 bytes at start of kernel */
#endif
.endm

.section ".start", #alloc, #execinstr
/*
* sort out different calling conventions
*/
.align
start:
.type start,#function
.rept 8
mov r0, r0
.endr

b 1f
.word 0x016f2818 @ Magic numbers to help the loader
.word start @ absolute load/run zImage address
.word _edata @ zImage end address
1: mov r7, r1 @ save architecture ID
mov r8, r2 @ save atags pointer

#ifndef __ARM_ARCH_2__
/*
* Booting from Angel - need to enter SVC mode and disable
* FIQs/IRQs (numeric definitions from angel arm.h source).
* We only do this if we were in user mode on entry.
*/
mrs r2, cpsr @ get current mode
tst r2, #3

第1页

TOP相关主题

你可能喜欢

  • linux内核启动分析
  • Linux内核分析
  • Linux内核配置
  • linux内核源码
  • linux内核移植
  • linux 内核解析
  • linux内核编译

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email