文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > Localized doping using silicon ink technology for high efficiency solar cells 0119
侵权投诉

Localized doping using silicon ink technology for high efficiency solar cells 0119

SE solar cell fabrication, CETC, Silicon ink, LD

LOCALIZED DOPING USING SILICON INK TECHNOLOGY

FOR HIGH EFFICIENCY SOLAR CELLS

K. Alberi, G. Scardera, H. Moutinho, R.C. Reedy, M.J. Romero, E. Rogojina, M. Kelman, D. Poplavskyy, D.L.

122

Young, F. Lemmi and H. Antoniadis

1

National Renewable Energy Laboratory, Golden, CO, USA

2

Innovalight Inc., Sunnyvale, CA, USA

1

2

1

1

1

2

2

2

ABSTRACT

Controlled localized doping of selective emitter structures via Innovalight Silicon Ink technology is demonstrated. Both secondary ion mass spectrometry and scanning ca-pacitance microscopy reveal abrupt lateral dopant profiles at ink-printed boundaries. Uniform doping of iso- and py-ramidal surfaces is also verified using scanning electron microscopy dopant contrast imaging.

INTRODUCTION

A selective emitter is a front-contact solar cell configura-tion in which surface regions under the front contacts are heavily doped to improve ohmic contact, while remaining surface regions are lightly doped to minimize charge carri-er recombination and improve blue light response [1-4]. Although theoretically able to achieve high conversion efficiency, in practice such gains are only realized if high localized doping is achieved on textured surfaces without also damaging charge carrier generation in the bulk Si material. In addition, even if technically feasible, in order to be commercially viable and widely implemented, the selective emitter manufacturing process must also be rela-tively simple, cost-effective and easily incorporated into existing production lines

In practice, selective emitter formation by conventional photolithography, laser-patterning, or etch-back tech-niques often fails to meet at least one of the above-mentioned criteria due to high cost, difficult process con-trol, defect formation and excessive lateral dopant diffu-sion, among other issues [5-8].

In contrast, implementation of the Innovalight Cougar Platform with Innovalight Silicon Ink allows solar cell pro-ducers to overcome these barriers. A portfolio of simple to implement technologies, the Innovalight Cougar Platform enables the manufacture of a selective emitter solar cell with a single-step non-masking diffusion. Innovalight Sili-con Ink is a highly engineered silicon nanoparticle colloidal dispersion, implemented for both high volume ink-jet and screen printing deposition, and further optimized to be produced and delivered in commercial volumes. In fact, demonstration of this technology using screen printing on monocrystalline 125 x125 mm Cz-Si wafers has resulted in efficiencies as high as 19% [10]. Here we present fur-ther details on the efficacy of localized doping by Si ink and demonstrate uniform doping on textured surfaces.

EXPERIMENTAL

Lateral and depth doping profiles of the selective emitter were investigated by secondary ion mass spectrometry (SIMS) and scanning capacitance microscopy (SCM). Multiple SIMS measurements were performed at various locations spanning two fingers of a Cougar device pattern. A complete contacting pattern with fingers and busbars was printed onto a saw damage etched wafer and sub-jected to a diffusion process. Ink regions were stripped prior to measuring. The SIMS measurements were per-formed on a Cameca IMS-5F. The impact energy of the

primary Cs+

ion beam, purified by a mass filter, was 14.5 keV at an incident angle of 25° from the surface nor-mal. The primary current was approximately 65 nA fo-cused into a spot approximately 40 µm in diameter. Nega-tive secondary ions generated from the sample were acce-lerated normal to its surface and were detected at 4.5 keV. The mass spectrometer was focused for high mass resolu-tion to separate the 31P signal from the 30Si1

H mass inter-ference. For depth profiles, secondary ions, counted by electron multiplier and Faraday cup detectors, were col-lected from a 60 µm diameter area in the center of a ras-ter-scanned 150 µm x 150 µm region. For imaging, sec-ondary ions from a 250 µm x 250 µm square area were collected minus 10% to minimize effects from the crater walls.

Localized doping was further verified by performing SCM measurements directly at the edges of Silicon Ink printed regions. Silicon Ink fingers were printed onto a polished wafer and subjected to a drive-in step. SCM measure-ments were performed on a Veeco Dimension 3100 mi-croscope with Nanoscope IIIa electronics and Pt/Ir-covered Si tips. The specimen surface was not polished in order to preserve the surface doping profile. Instead, the positions of the ink lines after printing were marked with a focused ion beam, the ink was stripped, and front and back metal contacts were deposited. The sample was then heated to 300 C for 20 minutes in air, with UV exposure during the last minute, to form a uniform surface oxide. Measurements were taken at the boundary of the ink-printed regions away from the FIB marks to determine the extent of lateral dopant diffusion.

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email