ML4803 240W Off-Line Power Supply with PFC
March 1999
Application Note 42043
ML4803 240W Off-Line Power Supply with PFC
INTRODUCTION
Included in this Application Note are a reference
schematic, ML4803 design equations, the circuit layout,and parts list. The reference schematic demonstrates howthe ML4803 can meet the requirements of a PFCcorrected power supply for desktop computer
applications. The design features include a low-cost singlesided PCB with 240W of output power, a form factorcompatible with desk top computer requirements, andline frequency harmonic content compliant withIEC1000-3-2.
THEORY OF OPERATION
The ML4803 Power Factor Control section uses an inputcurrent wave-shaping technique that senses the boostinductor current. It compares the inductor current
downslope during the off-time of the main power switchwith a ramp programmed by the PFC output voltagevariation. When the two signals intersect the off-time isterminated and the on-time is initiated for the remainderof the cycle. Any line or load transients to the PFC willcause the output to either surge or dip below its regulatedvalue. This will either increase or decrease the
programmed ramp dv/dt, increasing or decreasing the off-time of the main power switch and compensating for loaddemand. Unity power factor is maintained because thesensed inductor current ramp is proportional to the inputvoltage.
Electrical Specifications
Line voltage
Line harmonic contentSwitching frequencyPOUT
RegulationRipple
Efficiency @ 115VAC, 240W
85 to 265VACIEC1000-3-2
67kHz240W±0.1%30mVRMS
85%
PFC CONTROL CIRCUIT DESIGN
Internal Voltage Ramp
The internal ramp current source is programmed by way ofthe VEAO signal voltage (see Figure 1). This current sourceis used to develop the internal ramp by charging theinternal 30pF capacitor. Steady-state operation ensuresthat the VEAO signal is 5V. The frequency of the internalramp is set to 67kHz.One-Pin Error Amp
The ML4803 utilizes a one-pin voltage error amplifier inthe PFC section (VEAO). The error amplifier is in reality a35µA current sink, which forces 35µA through the outputprogramming resistor. The nominal voltage of the VEAOsignal is 5V and its range is from 4V to 6V. The boost
50
40
IRAMP (µA)
30
20
10
VEAO (V)

Figure 1. Internal Ramp Current vs. VEAO
REV. 1.0 10/25/2000
(max):75W 6 Spice-model in the Simulation 7 Transformer model Spice mode...off-line power supply with power factor correction(PFC) circuit( variable ...
8 3.1 3.2 PFC Start-Up Sequence With HA16141 ......for power factor correction and an off-line power supply switching controller. IC7 (UC3845) is...
A Magnetron Power Supply with Transition-Mode Zero-Voltage-Switching Inverter_互联网_IT/计算机_专业资料。Journal ofEnergy and Power Engineering 7(2013)1571...
PFC 功能的 90 W 开关电源的设计与 实验研究黄 贺 1,付金波 2,孟涛 1,...as a high-power-factor off-line power supply[J].IEEE Trans.Ind.Electron...
for power factor correction and off-line power supply switching controllers. ...Features ? Synchronized PFC and PWM timing ? Self oscillation with fixed ...
Flyback power supply with forced primary regulation_信息与通信_工程科技_...Off-line Switcher with Advanced Feature Set and Extended Power Range," ...
Easily interfaces with both opto and primary ...off-line power factor correction (PFC) ...simple 5 V, 5 W bias supply using the TOP200...
TPS 规范(Thin Power Supply Specification):具有 PFC(功率因数校正)、自动负载...(with the exception of a fault condition that has opened the AC line ...
Supply C2 0.01uF R5 28.7K CSA_RTN C5 1....Schematics- Power Board 650W PFC DEMO BOARD Rev...(with Cooling) Efficiency Vs Line Voltage 97.5 ...
3. Tolerance : includes set up tolerance, line ...4. The power supply is considered a component ...240W Single Output Industrial DIN RAIL with PFC ...
热门文档