MOTOMAN机器人
YASNAC-NX
共通パラメータ初期値表
12310646.xls
FD Byte Type (UCHAR) NOTE: FD parameters in this document describe only the meaning not availability. Availability must be checked before use. The items painted in purple are only for special customer. Almost all are not ready. NX 0 1 XRC Main Item 0 Concurrent IO 1 Relative job function Sub Item Step number extension Unit Remarks 0: 10000 steps (Standard) 1: 15000 steps (Extended) 0: Disable 1: Enable (Standard) 2: Enable ( new JOB created as relative JOB (the base frame is specified with S2C278) 0: Disable, 1: Enable 0: Disable 1: Enable 2: Enable API function (PCXRC only) 0: Disable 1: Enable 2: endless motion by instruction 0: Disable 1: 1 task 2: 2 tasks 3: 3 tasks 4: 4 tasks 0: Disable 1: 4tasks 2: 8 tasks 0: Disable, 1: Enable 0: Disable, 1: Enable Initial 0 0
2 3
2 External reference point 3 Data transmission
0 0
4
4 Endless rotation (Ext-axis, T-axis)
0
5
5 System job function
number of tasks (1 to 4)
0
6
6 Independent motion
number of tasks (4 or 8)
0
7 8 9 10
7 Coordinated motion 8 Function for MOTION debug 9 10 Function for shipping test (R)
Debug instruction MEASON, MEASOF instructions Deta transmission commands RABS, WABSO
0 0 0 0
11 12
13
11 <Deleted> ROTSY communication area using method Following register areas are 12 <Reexamined> I/O alarm/message detection (Bit detected. M060:d0-d15 system IO alarm 1-16 setting) M061:d0-d7 system IO alarm 17-24 M061:d8-d15 user IO alarm 1-8 M062:d0-d15 system IO message 1-16 M063:d0-d7 system IO message 17-24 13 Start Point Search
0 d0 :IO alarm, d1 :IO message 0: Numeral value (Standard) (Specific input code area) 1: Bit value (Register area) 0
0: Disable 1: Slow Down and Stop 2: Stop Immediately
0
14 15 16 17 18 19
14 <Deleted> IO Message history extension 15 Speed limitation for European safety specification 16 <Deleted> Observer status display 17 <Deleted> Condition change during test run 18 Station twin (triple) synchronous function (Multi-task synchronization) 19 PMT function 1: PMT with P.P operation 2: Addition of automatic PMT (SETTOOL, GETTOOL, PMT 20 Conveyer synchronization 21 22 Station twin (triple) synchronous function (Multi-task synchronization)
0 0: Disable, 1: Enable 1 0 0 0: Disable, 1: Enable 0: Disable 1: Enable with P.P 2: Enable automatically 0: Disable, 1: Enable 0: Normal 1: Controlled by master robot motion time (complete 0: Disable, 1: Enable 0: Disable, 1: Enable 0 0
20 21 22
0 0 0
23 24 25 26 27 28 29 30 31 32 33
23 24 25 26 27 28 29 30 31 32 33
Interrupt job COMARC function <Deleted> Shared control <Deleted> Working posture <Deleted> Force detection <Deleted> TURBO function General sensor TCP function <Deleted> ME-Net data link <Deleted> ME-Net computer link
0 0 0 0 0 0 0 0 0 0 0
1/8
NX FD
YASNAC-NX共通パラメータ初期値表12310646.xls

MOTOMAN机器人培训教材D... 200页 4下载券 motoman 6页 2下载券 MOTOMAN核心参数设置 8页 2下载券 motoman机器人 21页 7下载券...
(前提是机器人如装有三孔操作盒必须设定在预约 禁止状态) 工具资料之设定1 工具... MOTOMAN核心参数设置 8页 2下载券 motoman机器人 21页 7下载券 motoman机器...
9 5.4 熔化极气保焊实施的关键点 d)焊接电流与焊接电压(1)这两个参数是...SGM SGM 气孔 对策 焊接条件和焊接施工条件的设定 ?在处理填弧坑时,将电流...
示教前的系统设置包括 :1 ) 零位标定 2 ) 特殊点设置 3 ) 控 制器时钟设置 4) 干涉区域设置 5) 操作原点设置 6) 工具参数标 定 7) 用户坐标设置 8 ...
4.1 材料 ? 单通道 EtherNet/IP 卡 (P/N 154466-1) 包括 EtherNet/IP 卡和 ApplicomIO 电脑网络接口软件光盘 4.1.1 卡的设置没有板设置变化的需要。 4....
33 示教 功 能的实 现 . 示教面板上设置 了对应驱动机械手运动的各电机正反转 、 记录信息 、 清除记录( 包括最后一次信息和全 部信 息 )返 回示教 起...
实验中主要参数设置如下 : < C E 变换采样空间大小: !""H%*" . 屏幕上活动图像的显示的 位置和大小:屏幕左上角, !""H%*" . 内存缓冲区大小 : !""...
中断再焊接功能是机器人正在焊接时 ,因某种原因作业程序中断后 ,机器 人重新运行程序时 ,可根据使用者的设置 ,接着进行焊接或者停止焊接只完成剩余的动作. 而防...
、 条 件的 设置 等功能 这些 功能 的 实现 往往 在具 体的程 序 编制...0 . , 回车(此时系 统将 记录 当前 位 姿参数 以便 回放 再 现时 调用 )...
通信功能; (7)用户接口, 提供有效 的人/ 机界面, 方便用户操作及人工设置。...接口,Page51 机器人离线编程系统的核心技术是机器人及 其工作环境的图形描述。 ...
热门文档