文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > 无结合剂碳化钨非球面模具的超精密磨削加工_郭兵
侵权投诉

无结合剂碳化钨非球面模具的超精密磨削加工_郭兵

第50卷第13期 2014年7月

机 械 工 程 学 报

JOURNAL OF MECHANICAL ENGINEERING

Vol.50 No.13 Jul. 2014DOI:10.3901/JME.2014.13.190

无结合剂碳化钨非球面模具的超精密磨削加工

郭 兵1 赵清亮1 李洪亮2

(1. 哈尔滨工业大学机电工程学院 哈尔滨 150001; 2. 西安陕鼓动力股份有限公司 西安 710075)

摘要:针对无结合剂碳化钨材料,进行非球面模具的法向磨削试验研究。分析法向磨削非球面时的砂轮对刀误差对磨削精度的影响,研究无结合剂碳化钨非球面模具的磨削表面形貌特征和最终表面质量,优化误差补偿工艺,并利用聚焦离子束对磨削后的非球面亚表层损伤进行成像分析。研究结果表明利用推导的砂轮对刀误差方程,可以在磨削加工前对砂轮的初始位置进行精确调整,提高磨削加工精度。磨削后无结合剂碳化钨非球面模具不同区域的表面质量不同,距非球面中心越近,磨削质量越好,距中心越远,磨削质量越差。经过3次误差补偿磨削加工后,最终的无结合剂碳化钨非球面模具的面形精度误差均小于0.3 µm(PV值),表面粗糙度平均值小于8 nm(Ra值),亚表层没有明显的裂纹产生。 关键词:无结合剂碳化钨;非球面模具;超精密磨削;误差分析;表面质量;亚表层损伤 中图分类号:TG580

*

Ultra-precision Grinding of Binderless Tungsten Carbide Aspheric Mold

2

GUO Bing1 ZHAO Qingliang1 LI Hongliang

(1. School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001; 2. Xi’an Shaangu Power Co., Ltd., Xi’an 710075)

Abstract:The ultra-precision wheel normal grinding of binderless tungsten carbide aspheric mold is researched. The influence of grinding wheel initial position error on grinding accuracy is analyzed. The ground surface morphology and quality of binderless tungsten carbide aspheric are presented. And then, the grinding error compensation is optimized and the subsurface damage of mold is studied by focus ion beam. The results show that the grinding wheel initial position error model is useful to enhance the grinding wheel initial position accuracy. The morphology and quality of binderless tungsten carbide aspheric surface are inhomogeneous. The surface quality of aspheric center is better than that of aspheric edge round. Finally, after 3 times error compensation, there binderless tungsten carbide aspheric molds with 0.3 µm (PV) form accuracy and 8 nm (Ra) surface roughness are obtained, and no crack is found in subsurface of these molds.

Key words:binderless tungsten carbide;aspheric mold;ultra-precision grinding;error analysis;surface quality;subsurface damage

0 前言

非球面光学元件具有增加光学设计自由度、简化系统结构、减小仪器尺寸和质量等优点,是制造

[1]

微小型光电子系统的关键元件。在军用方面,欧、美、日等国家研制和开发的军用光电系统,如军用激光装置、热成像装置、微光夜视头盔、红外扫描装置等关键部件都不同程度上采用了非球面光学零[2]

件。在民用方面,非球面光学元件在数码相机、照相手机、车用摄像装置、DVD读取头、显微及望远镜以及数码摄像镜头的应用愈加广泛,需求量急* 国家自然科学基金资助项目(51075093)。20130709收到初稿,20140414收到修改稿

剧增加。

目前,高精度的非球面玻璃基光学元件的大批量生产主要依靠精密玻璃模压技术。其中,超硬非球面模具的超精密加工对最终产品的性能和成本起着决定性的作用。为了能够延长模具的使用寿命,此类模具材料逐渐由模具钢向硬质合金和精密陶瓷

[4]

发展。特别是无结合剂碳化钨,其不但具有的硬度、高耐磨性和高化学稳定性,同时还具有较大的

[5]

断裂韧性。因此与精密陶瓷模具相比,其机械加工性更好;与传统碳化钨材料相比,无结合剂碳化钨硬度更大,更耐磨损,同时还可以有效地避免由Co或Ni等结合剂与硬质合金颗粒的热扩散系数不同而引起的模具表面质量下降现象,因此无结合剂碳化钨已成为理想的精密玻璃模压用模具材料。

[3]

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email