搅拌槽 搅拌流场模拟 fluent
第47卷第6期 2011年3月
机 械 工 程 学 报
JOURNAL OF MECHANICAL ENGINEERING
Vol.47 No.6 Mar. 2011
DOI:10.3901/JME.2011.06.186
搅拌槽内固液悬浮特性的试验研究
杨敏官 来永斌
(江苏大学能源与动力工程学院 镇江 212013)
摘要:在直径为300 mm的平底圆筒搅拌槽内,对固相体积分数为1%~40%的固液两相体系的悬浮特性进行试验研究。利用固体激光器和数码相机,采用可视化方法详细分析固相体积分数、搅拌转速、颗粒性质和叶轮离底间隙对悬浮特性的影响。结果表明,悬浮高度主要受固相体积分数、颗粒直径和叶轮离底间隙影响;壁面颗粒堆积高度主要受叶轮离底间隙影响;槽底面中心区域和边缘角落区域是颗粒不易悬浮区,叶轮离底间隙和固相体积分数对槽底面何处颗粒最后悬浮有影响;较低的叶轮离底间隙有利于颗粒的悬浮,能获得较高的悬浮高度,但过低的叶轮离底间隙造成搅拌功率增大;壁面颗粒堆积高度降为零时的搅拌转速和悬浮高度达到液面高度85%时的搅拌转速均可视为固液悬浮操作的完全离底临界悬浮转速。 关键词:搅拌槽 固液悬浮 临界悬浮转速 悬浮高度 中图分类号:TQ 027.3+6
*
Experimental Investigation on Solid-liquid Suspension
Characteristics in Stirred Tanks
YANG Minguan LAI Yongbin
(School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013)
Abstract:Solid-liquid suspension characteristics in a flat bottom, cylindrical glass vessel of diameter D = 300 mm equal to the liquid height, stirred with a ZHX propeller are investigated. The particle volume fraction is from 1% to 40%. The effects of particle volume fraction, impeller speed, solid physical properties and impeller off-bottom clearance on the suspension characteristics are analyzed in detail by visual observations using a solid-state laser and a digital camera. The experimental results show that the suspension height is dependent on particle size, solids concentration and impeller off-bottom clearance. The settled particle-bed height at the tank walls is dependent on impeller off-bottom clearance. There are two zones at the tank base where the difficulty of suspension occurs, one just below the impeller and the other at the junction of the tank base and wall. The impeller off-bottom clearance and solid concentration have influence on the position where the final solid particles to be suspended come from. The suspension height increases with the decreasing of impeller off-bottom clearance, but power consumption increases as the impeller off-bottom clearance is reduced. The impeller speed when the settled particle-bed height becomes just invisible, or suspension height reaches 85% of the liquid height can be regarded as the complete off-bottom critical suspension speed in stirred tanks for solid-liquid suspension. Key words:Stirred tank Solid-liquid suspension Critical suspended speed Suspension height
0 前言
固体颗粒在液相中的悬浮操作是搅拌操作中很常见的类型,广泛地应用在化工、冶金、食品和制药等工业过程中。固液悬浮操作是借助搅拌器的作用,将颗粒分散到液相中,形成固液混合物或称悬浮液(淤浆),颗粒的悬浮会增大相接触面积,搅拌的作用使悬浮液强烈湍动,减小了颗粒表面的液* 国家自然科学基金资助项目(50776040)。20100331收到初稿,20100927收到修改稿
膜传质阻力,强化了传质,有利于化学反应的进行,提高了设备的生产能力。由于搅拌槽内三维循环和湍流多相流动的复杂性,学者们对单相搅拌体系进但是对固液悬浮体系的研究主行了较多的研究[1-2],
要集中在低浓度悬浮液的悬浮特性方面,如颗粒浓度分布和临界悬浮转速方面等。
悬浮高度是指搅拌槽内悬浮液层的高度,其上是清液层。悬浮高度是表示搅拌槽内固体颗粒悬浮状态的参数,也是固液悬浮操作重要的设计参数。迄今为止,有关悬浮高度的研究很少,并且其中一些文献对悬浮高度的研究是间接的,主要目的是研
在直径为0.34 m的无挡板平底圆筒搅拌槽内,采用PBT和ZHX两种搅拌桨对固相体积分数为20%的玻璃微珠-水固液两相体系的悬浮特性进行试验研究.采用固体激光器和数码...
偏心搅拌槽固液悬浮特性 以数值模拟对偏心搅拌时的固液悬浮特性进行了研究,物料选用固相体积分数为15%、粒径为135μm的球形玻璃珠-水两相体系,采用标准扛揣流模型...
平底圆筒搅拌槽内,采用PBT和ZHX两种搅拌桨对固相体积分 数为20%的玻璃微珠一水固液两相体系的悬浮特性进行试验研究.采用固体激光器和数码相机分 别研究了搅拌桨离...
人们对 固液悬浮进行了大量研究, 大都集中在颗粒浓度分布和 悬浮特性、临界悬浮转速、流体流动特性等方面. 对本 工作涉及的搅拌槽内固液两相流体系,Altway 等研 究...
搅拌槽内固液悬浮和气液分散的实验研究_能源/化工_工程科技_专业资料。第4 2... 搅拌槽内固液悬浮特性的... 18人阅读 7页 2.00 固液搅拌槽内液相速度...
34 m 的无挡板平底圆筒搅拌槽内 ,采用 PBT和 ZHX 两种搅拌桨对固相体积分 数为 20%的玻璃微珠 - 水固液两相体系的悬浮特性进行试验研究 . 采用固体激光器和...
搅拌槽内固液悬浮特性的... 暂无评价 7页 2.00 偏心搅拌槽固液悬浮特性...都荣礼等[1]对侧伸式搅拌槽气液两相 的传质系数进行了实验研究;Wesselingh ...
侧伸式搅拌器因其自身 的特点被广泛用于脱硫过程的...本研究对侧伸式搅拌槽的固液悬浮性能进行研究, 找出...因为本实验是在槽内无挡板的条件下进行 的,所以...
固液搅拌槽内轴向流动特性的实验研究_专业资料。在直径为300 mm的平底圆筒搅拌... 搅拌槽内固液悬浮特性的... 17人阅读 7页 2.00 Rushton搅拌釜内的气...
热门文档