钢铁行业资料
小孔法测量Cr-Ni奥氏体不锈钢焊接残余应力的适用
性研究
李荣锋 祝时昌 陈亮山
摘 要 应变释放系数A、B的标定试验发现,直到单轴拉伸应力达到0.73σs时,孔边屈服产生的塑性变形才发生,对Cr-Ni奥氏体不锈钢小孔法测量残余应力的影响小。同时经过小孔法和全释放法测量实际焊接残余应力及其分布的对比发现,只要选择恰当的应变片,使之与小孔孔径匹配,小孔法测量高残余应力,特别是焊接残余应力仍有较好的适用性。SUS321不锈钢的对接接头的纵向焊接残余应力最大值为540MPa,大大超过母材屈服强度。
关键词 适用性 小孔法 焊接残余应力 Cr-Ni奥氏体不锈钢
STUDY ON FEASIBILITY OF HOLE DRILLING METHOD FOR MEASUREMENT OF WELDING RESIDUAL STRESS
IN Cr-Ni AUSTENIC STAINLESS STEEL
Li Rongfong
WuHan Iron and Steel Corp.
Zhu Shichang Chen Liangshan
Institute of Metal Research Academia Sinica
Synopsis It is found out from calibration tests of strain relief constant
A & B that plastic deformation caused by the yield around the drilling hole has little influence on the measurement of the welding residual stresses in Cr-Ni austenic strainless steel by the hole drilling method since it does not occur till the drawing stress at the single axis approaches 0.73σs.In the meanwhile results from a comparision of the
measured value of the actual residual stress in Cr-Ni austenic strainless steel and its distribution by the hole drilling method with that by the section method indicate that the hole drilling method has better feasibility for measurement of high residual stress,and the high welding residual stress in particular provided the rosette of strain gauge is appropriately matched with the hole diameter.The peak of longitndinal residual stress in the butt weld joint of SUS 321 stainless steel is 540 MPa,which is far beyond the yield strength of the base metal.
Keywords feasibility hole drilling method welding residual stress Cr-Ni austenic steel
1 前 言
德国人Mather于1934年最早提出了小孔法测量残余应力技术[1]。此后,特别是50年代以后,许多国家的研究者对此方法进行了大量的研究,其间的成就包
73 s 时 ,孔 B 边屈服产生的塑性变形才发生 , 对 Cr - Ni 奥氏体不锈钢小孔法测量残余应力的影响 小 。同时经过小孔法和全释放法测量实际焊接残余应力及其...
更多>>以测量焊接残余应力为出发点,介绍了常用的测量方法,重点阐述了小孔释放法的测量原理和计算公式的推导,以及为提高测量精度而进行的释放系数的标定、塑性变形公式...
64 ? ElectricWeldingMachine 研究与设计 王江超等: 小孔法测量焊接残余应力 第2期 向应力, 并且 σr和σ1 的夹角为 φ〔4〕。 将式(6)代入式(7)积分可得...
用热处理方法消除奥氏体不锈钢焊接残余应力_机械/仪表_工程科技_专业资料。第 22...在焊态下进行焊接接头残余应力的测量时, 测 量方法采 用钻盲 孔测量 法, ...
本研究在现有条件下,选择技术上比 较成熟、 国内外广泛应用的测试方法,即利用盲孔法测量了高频焊管道焊接接头 纵焊缝的残余应力。 小孔法的原理是在应力场中钻小孔...
影响机理研究 2007 2.李荣锋 Cr-Ni奥氏体不锈钢焊接残余应力小孔法测量技术 ...本文论述了焊接残余应力的产生原因,介绍了残余应力的测试方法及其特点和发展方向,...
盲孔法测量镍基合金焊接残余应力测试技术机械科学研究院哈尔滨焊接研究所(150080)...李荣锋 Cr-Ni奥氏体不锈钢焊接残余应力小孔法测量技术 1996(06) 4.CB 3395-...
焊接残余应力的测定_能源/化工_工程科技_专业资料。焊接残余应力的测定辽宁石油化工...1、应力释放法主要包括切条法、切槽法,小孔法,逐层铣削法等,这里 主要介绍切...
用热处理方法消除奥氏体不锈钢焊接残余应力_机械/仪表_工程科技_专业资料。焊接残余应力的分析研究维普资讯 http://www.cqvip.com Edited by Foxit Reader Copyright...
奥氏体不锈钢焊接的缺陷分析及解决办法陈 炜① ( ...焊接构件做高于 820 ℃热处理来消除焊接残余应力。...
热门文档