[µm]
(1)

t – solidification time [s]
The relations between the mechanical properties and the structure given by the constants in the Hall-Petch relation are rendered by the equations


[MPa]
(2)
For a circular section the value of sphericity factor is 1 while for more complex shapes it is >1 (Fig. 1). It responds sensitively to changes in the geometry of inclusions and internal cavities, which are connected with changes in mechanical properties. Pores with the sphericity factor s>1 exhibit, under identical porosity P, a higher measure of matrix interruption than spherical pores with s=1, which corresponds to a porosity that is higher by factor s.
With increasing factor s the notch effect of pores increases, the appearance of cracks in the structure increases and this shows up in the strength of the material. To determine the mechanical properties Rm and Rp0.2 the following relations are used [2]:
) [MPa] Rm=Rm(1 sP
o
(5) (6)
[MPa]
(2a)
Rp
0,2
=Rp0,2(1 P) [MPa]
where K2, K4in the range from 1 to 10 mm.
DAS in castings ranges from 10 to 150 μm. The larger the spacing, the greater the probability of the occurrence of porosity and shrinkages. The goal is therefore to have this spacing as small as possible.
The magnitude of DAS is connected with a number of other structural phenomena. The finer the structure (i.e. lower DAS value), the smaller the segregation distances. Thus when the extent of segregations is smaller, there appear smaller particles of intermetallic inclusions. Impurities are separated as separate particles in interdendritic spaces, the chemical composition of the alloy is more homogeneous, and micro porosity is distributed more favourably.
To obtain a fast quantitative determination of the geometric parameters of the structure (inclusions, hollow spaces) the shape factor f or its reciprocal value, the sphericity factor s is used.

where Rm, Rp0.2

are the ultimate strength and yield point of porous material [MPa]
Rm, Rp0.2 are the ultimate strength and yield point of material without pores [MPa]
The porosity of die-castings is usually due to the appearance of a combination of micro shrinkages and blow-holes. When the mechanism of blow-hole formation predominates, the pores are rather of the spherical shape; if the micro shrinkage mechanism predominates, the cavities are of ragged shape and copy the dendritic structure of the metal. (7)
[-]
Sp is the pore area [mm

2]
S0 is the total selected area of metal [mm2] P is the porosity [%]
[-]
(3)
2. Experimental part
The subject of experiment was a spark-ignition engine, cylinder block of type designation EA11103D (Fig. 2)
4 valves /
2 valves /
(4)
where Ap is the blow-hole circumference [µm] U is the perimeter of cross-section area of structure element
2[μm]
s=1
Fig. 1. Shape of pores with different sphericity factors “s”
s=2 s=3 s=4s=5
94
ARCHIVES of FOUNDRY ENGINEERING Volume 12, Issue 1/2012, 93-98

readdata1。市场营销计划白象方便面市场营销计划 一、 市场分析(一) 企业的目标和任务 如今随着生活节奏的加快,方便面市场前景广阔,消费者众多,不同口味与 品牌的...
readdata1_IT/计算机_专业资料。多媒体实验● 授课内容:理论讲授,实践练习,作品欣赏 ● 考核形式:期末考试,实验作品 ● 实验上传: ftp://10.2.210.170:22 ...
readdata1_专业资料。h劳教所 2008 年工作总结 劳教所 2008 年工作总结 2008 年,我所在省厅、局的正确领导下,以“三个代表”重要思想和党 的“十六”大精神...
readdata1 隐藏>> 安徽农业科学 , Journal of Anhui Agri Sci 2009, 37 ( 25) : 11864 - 11866 . . 责任编辑 陈秀晨 责任校对 况玲玲 植物抗旱 、 ...
readdata1 9页 免费 readdata1 3页 2财富值 readdata1 2页 免费 readdata1_new 3页 免费搜你所想,读你所爱 拒绝盗版,营造绿色文库 如要投诉违规内容,...
3页 免费 副本readdata1 暂无评价 2页 免费readdata1 暂无评价0人阅读0次下载举报文档 励志文章...
readdata1_法律资料_人文社科_专业资料。澧县城关中学 九主备教师 吴学福 ...第 吴学福 2013 年 新授课 月日节 知识与技能教学目标过程与方法 1:了解 02...
readdata1_政史地_高中教育_教育专区。15.期末综合测试卷(三)一、在下面几组词语中,拼音完全正确的一组是( ()(2 分) 。 1.cāng jìng 苍劲 3.gu...
readdata1 古诗教学随笔古诗教学随笔隐藏>> 古诗词赏析与积累浅见仰望历史的星空,散落在苍穹上的星斗,灼灼其华。我愿把文学 大家们的经典文字,视为闪耀的星辰。...
热门文档