CSR-6145规格书
DRAFTSerial Interfaces
1Reset the SPI interfaceHold SPI_CS# high for two SPI_CLK cycles
2Write the command wordTake SPI_CS# low and clock in the 8-bit command
3Write the addressClock in the 16-bit address word
4Write or read data wordsClock in or out 16-bit data word(s)
5TerminationTake SPI_CS# high
Table 7.3: Instruction Cycle for a SPI Transaction
With the exception of reset, SPI_CS# must be held low during the transaction. Data on SPI_MOSI is clocked into
the BC6145 QFN on the rising edge of the clock line SPI_CLK. When reading, BC6145 QFN replies to the master
on SPI_MISO with the data changing on the falling edge of the SPI_CLK. The master provides the clock on SPI_CLK.
Taking SPI_CS# high terminates the transaction.
Sending a command word and the address of a register for every time it is to be read or written is a significant
overhead, especially when transferring large amounts of data. To overcome this BC6145 QFN offers increased data
transfer efficiency via an auto increment operation. To invoke auto increment, SPI_CS# is kept low, which auto
increments the address, while providing an extra 16 clock cycles for each extra word to be written or read.
7.2.2Multi-slave Operation
Avoid connecting BC6145 QFN in a multi-slave arrangement by simple parallel connection of slave MISO lines.
When BC6145 QFN is deselected (SPI_CS# = 1), the SPI_MISO line does not float. Instead, BC6145 QFN outputs
0 if the processor is running or 1 if it is stopped.
7.3I²C Interface
PIO[8:6] are available to form a master I²C interface. The interface is formed using software to drive these lines.
Note:
The program memory for the BC6145 QFN is internal ROM so the I²C interface only connects to a serial
EEPROM, Figure 7.2 shows an example. The EEPROM stores programmable audio prompts, see Section
14.1.4, as well as PS Keys and configuration information. The programmable audio prompts option requires a
larger EEPROM than Figure 7.2 shows, up to 512Kb.
When a SPI flash is used to store programmable audio prompts, see Section 7.4, an EEPROM is still required
to store the PS Keys and configuration information.
The EEPROM Supply in Figure 7.2 is 1.9V.
3

.
PIO[8]5.7
PIO[6]020
PIO[7]000

-
WT
-G
Figure 7.2: Example EEPROM Connection
7.4SPI Flash Interface
PIO[23, 20, 11, 3] form a software-driven master SPI flash interface, Figure 7.3 shows an example connection to a
serial SPI flash IC.
Advance Information
CS-204118-DSP1A© Cambridge Silicon Radio Limited 2010Page 25 of 68
This Material is Subject to CSR's Non-disclosure AgreementDRAFT_`SNQR=nck Data Sheet
蓝牙模组CSR方案BC6145规格书_电子/电路_工程科技_专业资料。出口蓝牙音箱最多...CS CLK MOSI GND 30 29 28 27 26 25 24 23 22 21 20 VBAT LED1 LED0...
BC=1889KM BB=1921KM BA=1953KM 第 1 组数据 ...37=6145KM 36=6177KM 35=6209KM 34=6241KM 33=...93C46 或 93CS46 共 128 字节 本运算适合 92-...
bc =3.5 w/㎡℃ 故 Q bc = K bc Fbc (tn...遮挡系数 Cs=0.74,遮阳系数 Cn=0.6 2:30 12 ...6145 1958 2036 8 953 156 371 9 1470 423 881...
BC=1889KM BB=1921KM BA=1953KM 第 1 组数据 ...37=6145KM 36=6177KM 35=6209KM 34=6241KM 33=...93C46 或 93CS46 共 128 字节 本运算适合 92-...
热门文档