flow3d泥沙模拟
This model predicts the advection, erosion, settling and deposition of sediment, such as sand. The scour sediment model can be used in any type of flow, though all sediment motion must take place within one fluid. The settling component of the model presumes the sediment particles to be spherical and their velocity to be small (so that viscous effects predominate in the flow around each sediment particle)–see the Drift Model for Two-Phase Flow. The settling (drift) coefficient is automatically calculated as
Here SCRDIA is the average particle diameter. RHOF is the density of the fluid, and SCRRHO is the density of the sediment particles; a typical value for sand is 2.65g/cm. The “lift” component of scour is an empirical model based on Bed-Load sediment transport models; the lift velocity
Here τ is the magnitude of the shear stresses at the interface and is the macroscopic 3fluid density. SCRALP is an empirical parameter to adjust the rate of scour erosion for the particular application. Its default value is 1.0, based on experimental data with sand. τc is the critical shear stress. Where the shear stress is greater than τc, scour erosion occurs because the forces that cause the sediment particles to lift exceed the forces keeping the particle from lifting (gravity, cohesive forces to neighboring particles). Conversely, where the local
magnitude of shear stresses is less than τc, the liquid forces are insufficient to causes particle at the surface to lift, and sediment subsequently deposits according to the settling (drift) velocity. The critical shear stress, τc, is computed from the critical Shields parameter, SCRCRT:
Here g is magnitude of gravitational acceleration.
Sediment is considered packed if the sediment volume fraction is greater than or equal to SCRFCR; the packing density is equal to SCRFCR×SCRRHO.
Thus, regions where the sediment concentration (in units of gm/cm3 in CGS) is equal to or greater than SCRFCR×SCRRHO are packed and fluid flow does not occur – the drag imparted on the liquid by the sediment is assumed to be infinite (i.e., the inverse liquid drag quantity, the drag coefficient computed by FLOW-3D is zero). In regions where the sediment volume fraction is greater than SCRFCO, but less than SCRFCR, the drag model is activated (see Solidification Drag Model). SCRDRG in this model is equivalent to TSDRG (the default value is 1.0). When the solid fraction of sediment is less than SCRFCO, the drag model is not activated, but the viscosity is enhanced according to:
Here μ0 is the fluid viscosity and μ is the enhanced viscosity due to the presence of sediment. Both the drift and lift velocity equations can be easily customized in the routine scour_drift.f



Sediment Transport Mod... 17页 免费 Sediment Scour Model 4页 1下载券 ...Generation mechanism – Sediment transport and flow patterns – Only for ...
沉积物冲刷模型 (Sediment Scour Model) 例如桥墩周边的侵蚀现象; ? 卷气模型(Air Entrainment Model) 流体在流动过程中卷入少量空气的问题; ? 浅水模型(Shallow ...
the effect of relative sediment size on pier scour depth using three uniform sediment sizes and three bridge pier designs at different geometric model ...
of sand river bed, no bed load sediment Presence 10.5 mm pebbles reduces erosion 2009 FLOW-3D European User Conference FLOW- Scour Potential Model ? ...
The scour depth below the pipeline was determined using a regression model ...where s* = yS0/Dd50 dimensionless Shields parameter related to sediment ...
悬浮沈积模型假设– 漂移, 沈淀以及重新悬 浮 22 FLOW SCIENCE Sediment scour model 平均粒子直径 粒子密度 临界护罩参数冲刷侵蚀参数 -控制侵蚀率 临界packing分数...
淤泥池 上海析模计算机科技有限公司 Hydraulics physical model ? ? ? ? 沉积物冲刷模型 (Sediment Scour Model) 卷气模型(Air Entrainment Model) 浅水模型(...
degradation, bank failure, local scour around structures, formation of river ...SUTRENCH-2D: A ?nite-volume hydrodynamic and sediment transport model ...
悬浮沈积模型假设– 漂移, 沈淀以及重新悬 浮 22 FLOW SCIENCE Sediment scour model 平均粒子直径 粒子密度 临界护罩参数冲刷侵蚀参数 -控制侵蚀率 临界packing分数...
Sediment Scour Model Sedimentation & Scour Model ? 模拟沈积物的侵蚀、移动和沈 淀 ? 飘移的沈积物会在静止的流域 沈淀,变成河川底床的一部份 ? 沈淀后的...
热门文档