Page
1/9
SERVICE MANUAL Machine Title << CONDITION>>
Manual No. MSX-805 MSG-805 MSC-805
SE-CL201AX05-01 Component
CL1500 CL2000
Controller
Axis Drive
Adjustment of Zero Return Position for Z-Axis
Z-axis zero return position adjustment is required following servomotor/pulse-coder replacement or loss of parameter data. “ Z70 No. Z70
ABS. ILLEGAL
000n
Z” is displayed on the NC ALARM screen.
ABS. ILLEGAL
000n
NC ALARM MESSAGE Z
<< METHOD>> Establishment of the Z-axis zero return position is necessary. Establishment and Adjustment of the zero return position for Z-axis using following procedure.< Attention> Determinant of Z-axis zero return position based on Spindle Large Nose. For checking distance from Spindle Large Nose to zero return position, need to remove the chuck from the machine. So this manual considers zero point reference indexes (zero point index marks) is Z-axis zero return position. (Refer to<< REFERENCE>> on last pages about exact distance from Spindle Large Nose to zero return position.)<< INTRODUCTION>> 1. 2. 3. 4. 5. 6. 7. 8. 9. 3 2 1 Version
Set the“ ZERO POINT ADJUSTMENT” to“ VALID” on OPERATION PANEL screen to enable axis travel. Position the Z-axis to the machine zero point (Z-axis zero point index marks matches). Display the ABS. POSITION SET (Absolute Position Set) screen. Perform Z-axis initial setting on ABS. POSITION SET screen. Set the Z-axis“ ORIG-RTN” (Origin Return) on ABS. POSITION SET screen. Establish of the Z-axis zero return position. Reset the NC power following zero return position establishment. Following power on, perform Z-axis zero return operation to confirm positioning. Check the operation of the Z-axis in both of Manual and MDI operation.
2007/2/16 New Version YY/MM/DD Changes Specified Production Month Approval Machines From For Electronic Yoshida Distribution October 2000 (No.1)
Sakai Corrected By Issued By Sakai
CF2165-901A-02

日本森精机机床维修培训资料之NV5000刀库原点调整_机械/仪表_工程科技_专业资料...刀库原点复归位置调整 ·将W-轴控制参数NO.1010改为3.(在设定变更后)………...
日本森精机机床维修培训资料标题MORI SEIKI SL2500Y刀塔(分度+动力头)原点回归...见图1。 盘环螺栓 棘爪 图1 齿轮箱 动力头固定架 2.在区域调整模式下设置...
日本森精机机床维修培训资料之DCG张金标_机械/仪表_工程科技_专业资料。日本...3 是 需要建立原点回归, 再作负载调整吗? 不是 4 设定自动栅格位置设定有效 ...
森精机NL系列GM代码_机械/仪表_工程科技_专业资料。Moriseiki(shenzhen) ...对形状补正画面的 X,设定从主轴中心到刀塔在原点复归位置时旋转刀具中心的距离...
森精机20角刀塔规格的NL系列已开始接受订购_专业资料。从2007年7月9日起,森精机20角刀塔规格的高精度、高刚性车床NL1500和NL2000系列已开始接受订购。...
日本森精机机床维修培训资料之第5回研修NV4000鲁辉_机械/仪表_工程科技_专业...项的位置作为第2原点复归位置,把此时的机械坐标设定在 NC参数 No.1241“ X ...
日本森精机机床维修培训资料日本森精机机床维修培训资料隐藏>> 第5回中国售后服务...(A内XY第3原点,B内X第3Y第1原点) . ↓ . APC门开 ↓ Pallet放松 ↓ ...
机床程序原点设置与偏移 暂无评价 1页 免费 日本森精机机床维修培训... 17页 7下载券 FANUC绝对原点机床原点设... 2页 4下载券 机床回不了机械原点故障......
FANUC系统(日立,牧野,森精机)常见故障诊断与处理...后按上述常规方法分别对 YZ轴执行 ,, 原点回归操作...不严; ) (着2 座确认用的压力开关损坏或设定错误...
森精机20角刀塔规格的NL系列已开始接受订购_专业资料。从2007年7月9日起,森精机20角刀塔规格的高精度、高刚性车床NL1500和NL2000系列已开始接受订购。...
热门文档