IEEE TRANSACTIONS ON SEMICONDUCTOR MANUFACTURING, VOL. 7, NO. 3, AUGUST 1994
397
~ontourplot:49441 KH .‘IO,‘RL
18-JUL-91 16:14 Pogo 1
Contourplot:49681
18-JUL-91 16:37 Pago 1 BX, 0 2, FZ KH= 10, R L 75
DZ€2 TWL
= 75
-0.
T
-0. V A
-0.
LF
LF
-DZ€2 -Fig. I . TWL
__ BX _______.I.. FZ
BZ
Fig. 8.
TABLE I11
BONDING PARAMETERS“IDEAL” PROFILE FOR Wire Length KH (mill RL (milil0) LF (%) VA(psi) 150 mil 10 92 113 10 175 mil 10 15
120 10
Comments Same Unexpected Expected Same
K H= 10 RL= 75 LF116-120 VA8.5-10
K H= 10
KH=8
KH=8 150 Not applicable (Fz< -15 mil)
RL=113 Not applicable ( F Z -14 mil)~
RL= 75 LF115-120 VA8.5-10
RL=
Step 1. Look for those regions in the charts in which Ez is 5 - 6 mils and Dz is 9-10 mils. These regions can be located in the following four (4) charts:
KH= 10
RL= 75
KH= 10 R L= 113
KH=8
RL= 75
KH=8 RL= 150
Step 3. In Figs. 9 and 10, the wire is reasonably straight between point D and point F in each of the regions defined above. As an example, take KH= 10, RL= 75, LF= 120, and VA= 10, and the model predicts that the resulting loop should have Gx= 0.3 mil, BX= 0.12 mil, BZ= 3.9 mil, EZ= 5.8 mil, DZ= 9.5 mil, DX= 7.8 mil, IX= 64 mil, Jx= 93 mil, Kx= 112 mil, LX= 140 mil, FX= 165 mil, Fz= -12.4 mil, and TWL= 187.8 mil. Fig. 1 1 is the side view of this predicted wire showing it is reasonably straight between point D and point F. IV. CONCLUSION
Region defined in each of the charts is: (respectively) LF116-120 VA5.5-10 LF100-103 VA8.5-10 LF115-120 VA2-10 LF75-85 VA8-10
Step 2. Fig. 8 displays the corresponding area of the optimized chart to meet the“no wire sag” requirements (Fz> -13 mil), and the“not much wire stress close to bond ball” requirement (Bx-0 mil):
We have reconfirmed that the response surface methodology does indeed allow us to define the bonding parameters required to produce the“ideal” loop profile for greater than 175 mil wire length. If we chose to change the loop profile the data already exists from the charts generated. As can be seen in Table III and IV, the changes in the bonding parameters and the changes in the loop profile from 175 mil to

WIRE BOND PROCESS INTRODUCTION CONTENTS ASSEMBLY ...Multimode Transducer System Programmable profile, ...Bond Pad Pitch Ball Size Ball Thickness Loop ...
ASSEMBLY FLOW OF CIS ? Wire Bond Theory ? M/...2.5 um ?Fine Pitch Capability ?35 mm pitch @...loop Prepared pad By Hawk Long Source:NA Camtech...
Capillary interferes with 1st bond ? Used cap (PBGA 45um) with profile ... New Generation 4N wire for super-long loop, for fine pad pitch (Flex ...
file://C:\Wire-Bond-Inspection-Tools.html 9/17/03 Assembly - Wire ...D. Use the Fine/Coarse focus knobs to bring the top of the wire loop ...
Loop J-Wire II RF Loop II Security Bond II ...Long Wire, Fine Pitch, QFP, PLCC, SOJ, LOC,...J-Wire Loop Profile J-Wire GUI Screens Following...
UL loop ? by ESEC February 2004, High ...Assembly Solutions 10 CONFIDENTIAL Bond modes - IF...s due to small capillary IC ( fine pitch ) ?...
Wire Bond Loop Profile Development for Fine Pitch -Long Wire Assembly [J]...系统仿真学报,2006,18(11): 3058-3062。 作者简介 :周洪军(1985-),男,硕士...
PROFILE Z-axis EFO Ball bond Looping Search wedge Wedge bond Search ball ...long loop bonding Low temperature bonding Fine pitch / fine size bonding ...
ASM焊线(wire bond)摆线探索_机械/仪表_工程科技_专业资料。ASM焊线工艺探索...3 kink 的 loop profile 昨天用 BGA-last loop 打出来 的效果如左图, 这是...
Stitch Bond Enhancement For X-Wire Insulated ...assembly process flow, with minimal capital ... Fine Pitch Copper Wire... 8页 免费 Wire ...
热门文档