Hoisting Standard Operating Procedure 吊装作业标准操作程序 详细程序 吊装安全操作

④. Being close to ground staff during lifting transportation.
⑤. Equipment failure during lifting.
5.5
5.6 Slow start, slow stop by pressing the button half of the depth(the first gear). The driver must confirm no interference and join between each jib(crane) in flowing
line area before starting.
5.7
5.8 It is not allowed to use the limiter as a means of stopping. The driver must know the weight of the cargo before lifting; It is prohibit to test the
weight with overload protection.
5.9 Binding and hanging methods must comply with the standard instructions.
5.10 It is forbidden to make the cargo staying or going through the top of any personnel’s
head.
5.11 The cargo must be lifted 0.5-1 meter higher than the maximum height of the
equipments on the ground before reaching the lifting channel from the start point; then the cargo must be lowered to make it to the height of 0.5 meters from the ground when reaching the channel.
5.12 The driver must send an alarm signal continuously and drive through after the
personnel making way in case the hook or the cargo has to pass overhead of any person.
5.13 The cargo must be landed down to the gournd,platform or jigs slowly and
immediately;It forbids any person standing below the suspended cargo and keep the suspended cargo unattended.
5.14 It is allowed to hold the cargos only when the cargo is landed down within 1 meter
distance from the plane where the operator stands.
5.15 Any person is prohibited to move with the hook or the hanging cargos.
5.16 It is prohibit to lift one cargo together with two cranes cooperation.
5.17 The drivers must obey the “Ten non-lifting cases” strictly :
①. No lifting if command signal is not clear (two or more person coopration) or illegal
003-吊装作业hoisting work JHA_能源/化工_工程科技_专业资料。Shell STC ... 熟悉安全程序和规定,正确佩戴个人 PPE,持本人胸卡进出指定厂区; Lifting work ...
Standard operating pro... 6页 免费 吊装作业SOP Hoisting ... 12页 2...Executive Office 行政办公室 Standard Operating Procedure 标准运作程序 STANDARD ...
吊装作业安全管理标准 Safety management standards of hoisting 2013 – 11 – ...3.6 作业半径 operating radius 吊物中心的垂线与吊臂回转中心之间的水平距离。...
吊装作业SOP Hoisting St... 12页 5财富值 Software Testing 16页 免费 ... Standard Operating Procedure Standard Operating ProcedureStandard Operating Proce...
吊装作业安全管理标准 Safety management standards of hoisting 2013 – 11 – ...3.6 作业半径 operating radius 吊物中心的垂线与吊臂回转中心之间的水平距离。...
吊装作业安全管理标准 Safety management standards of hoisting 2013 – 11 – ...3.6 作业半径 operating radius 吊物中心的垂线与吊臂回转中心之间的水平距离。...
Standard operating proce... 6页 免费 吊装作业SOP Hoisting St... 12页 ...Wright LB-028-1.1 Standard Operating Procedure for Tracking Priority Projects...
吊装作业SOP Hoisting St... 12页 5财富值 XRD Standard Operating P... ... Standard Operating Procedure for Using the DEP LIMS Browser and Cost ...
to make sure it is in safe operating condition... as per the C-GS-10-10-1 procedure, the ...hoisting machinery must be made by a competent ...
山东普洛得邦 标准操作规程 STANDARD OPERATING PROCEDURE 页码:2-1 保安安全操作规程 文件编号:SOP.0023.00 替代:/ 生效日期:2013 年 12 月 12 日分发号: 一 ...
热门文档