文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > Hi-Pot Test for Fax SOP(传真高压测试作业规范)
侵权投诉

Hi-Pot Test for Fax SOP(传真高压测试作业规范)

Hi-Pot Test for Fax SOP(传真高压测试作业规范)

5. Test Location and Environment Control [测试场所和测试环境 测试场所和测试环境] 测试场所和测试环境

22±5℃ , 55±5%RH [温度范围:22.0±5℃,湿度范围:55±5% R.H.] 6. Test Procedure [测试步骤 测试步骤] 测试步骤 Ground step1.Check the base function of test machine,specially define the Fax function. Tip&Ring P1 [步骤1. 检查整机的功能,特别是Fax功能的确定.] step 2.Connect the machine to Extech 7440 dielectric strength tester,as P1 show. [步骤2. 按右图P1示的接线方法将被测物和7440测试仪连接.] step 3. Turn on the 7440 tester,press AC-W key ,enter the offset setting.Connect the 7440 Return line to the Current H.V.line,then press Test key,the result show the tester's own offset. [步骤3. 7440 offset: 打开7440电源开关,按AC-W键进入offset设定.将7440 Return线和H.V.线 接成环路,按Test键测试,结果即为仪器本身的漏电流. step 4.Set the parameter on the 7440 tester include: test Voltage,HI-Limit,LO-Limit,Ramp time,Dwell time. [步骤4. 设定7440参数:测试电压、电流上限、 电流下限、缓升时间、测试时间.] step 5.Press the Tset key to test. [步骤5.按下Test键进行测试.] step 6. The test pass will have a "du" sound,the LCD will show Pass and the green light will turn on.If the test fail, the red light will turn on and the alarm will on until you turn off. [步骤6.测试通过,将会响一声短暂的“嘟”声,同时显示屏显示Pass,Test键绿色指示灯也将会亮.如果测试失败,则红色指示灯亮起, 则红色指示灯亮起,并响起警报音直到你关闭为止.] step7.Check test machine function again. [步骤7.再次检查整机的功能.] step8. Store test result pictures and record the test data. [步骤8. 保存测试结果图片并记录下测试数据.]

+

Hi-Pot Test for Fax SOP(传真高压测试作业规范)

上一页第2页

你可能喜欢

  • 耐压测试培训
  • 耐压测试标准
  • SOP作业指导书
  • 测试原理
  • 液晶工艺
  • 高压测试
  • 软件测试规范

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email