先进材料上关于太阳能电池的经典文献
Robust Inter-Connecting Layer for Achieving High A
Performance Tandem Polymer Solar Cells
Jun Yang ,*Rui Zhu ,Ziruo Hong ,Youjun He ,Ankit Kumar ,Yongfang Li ,and Yang Yang * ecently, polymer solar cells (PSCs) have attracted much atten-R
tion primarily due to their potential for fabricating low-cost and
[1–3large-area exible solar cells. ] Smart chemistry can design
conjugated polymeric structures for PSCs with enhanced open-circuit voltage ( VOC ) and short-circuit current density ( J SC). This has resulted in signi cant ef ciency enhancements in recent years. Nonetheless, most of the materials designed today always suffer from the inherent disadvantage of not having a broad absorption range, which limits the utilization of the full solar
[4spectrum. , 5 ] A possible solution is to stack multiple photo-active layers wherein the photoactive layers have complemen-tary absorption. Recently, multiple-junction tandem PSCs with
various con guration have been demonstrated, in which two polymer:fullerene bulk heterojunctions (BHJs) are connected
[6–8]in series or parallel to ful ll this goal. These con gurations
enable reduction of potential loss during photon-to-electron conversion process, and add-up of electrical potential or photo-current of the individual BHJs, while the combination of poly-mers with complimentary bandgaps broadens absorption band ranging 300 nm up to 900 nm, covering a larger portion of the solar spectrum. Recently, a 7.7% PCE from small organic
[9]molecule-based tandem solar cells has been achieved. It
strongly indicats that tandem structure is one of the promising approaches to break though 10% theoretical limit for single-[10]junction-based polymer solar cells.
In addition to the requirement for photoactive materials,
a serial-connected tandem cell requires an inter-connecting layer (ICL) that joins the sequential subcells. It has to satisfy the following requirements. The ICL must ensure resistance-free electrical connection between subcells therefore there is no/minimal electric potential loss. The ICL serves as charge recombination zone aligning the quasi-Fermi level of holes in one subcell to that of electrons in the other, in which charge car-riers recombine consequently. Optically, it must be transparent to minimize absorption loss in the ICL. Most importantly, from the point of view of realizing successful tandem cells, the ICL should be physically robust to protect the underlying layers
J. Yang ,Dr. R. Zhu ,Dr. Z. Hong ,A. Kumar ,Prof. Y. Yang Department of Materials Science and EngineeringUniversity of California Los AngelesLos Angeles, CA 90095, USA
E-mail: jun.yang@ucla.edu; yangy@ucla.edu Dr. Y. He ,Prof. Y. Li Beijing National Laboratory for Molecular ScienceInstitute of Chemistry
Chinese Academy of SciencesBeijing, 100190, P. R. China
DOI: 10.1002/adma.201100221
against damage from further solution processing of the rear
subcell.
The ICLs consisting of n-type metal oxides combined with
high-workfunction metallic poly(3,4-ethylenedioxythiophene):-poly(styrenesulfonate) (PEDOT:PSS) have been used for
[8,11–13]tandem polymer solar cells. Commercially available
PEDOT:PSS which has been used in these previous reports has good lm formation properties, suf cient electrical conductivity and high optical transparency. Unfortunately, processability has become the top critical issue to design and fabricate a suc-cessful tandem PSC. The reason is that PEDOT:PSS lms have a thickness of only several tens of nanometers, and metal oxide layers are normally amorphous and not dense enough to pro-tect the lower layers (front subcell) when depositing the second subcell (rear cell) by solution process. The penetration of sol-vents through the ICL may disturb charge carrier selectivity of the ICL between the two subcells, and thus enhance the charge recombination loss. Therefore, reduced V has been widely OC
observed from tandem cells using these materials as ICLs.
Currently, fast-drying solution process of the rear subcell
(using solvents with low boiling point, such as chloroform or dichloromethane) is being used to partially circumvent this
[8]problem. , 11–13 It has been well understood that for single BHJ
PSCs the optimal processing parameters vary signi cantly with different type of polymers. However, this limits the choice for processing the rear cell, and thus its performance in tandem architectures. Its processing cannot take full advantage of well established processing methods for achieving maximal ef -ciency, for example, a slow growth solvent annealing approach, addition of high boiling point tertiary solvent, and using a high
[3boiling point solvent in general. , 14–16 ] Obviously, the existing
ICL materials, in spite of their many features, have fatal aws to be utilized as a reliable approach for tandem PSC design and ef ciency improvement. It is to ful ll this technology gap that we need a multi-functional ICL to sustain the solution deposi-tion of the rear layer. In this work, a modi ed PEDOT:PSS (m-PEDOT) layer was developed to be physically robust enough to endure slow drying solvents such as chlorobenzene (CB) and dichlorobenzene (DCB). Furthermore, we are able to modulate the optical eld distribution in the devices by varying the thickness of the ICL, as con rmed via optical simulations. This ICL widely broadens the solvent selection for the secondary active layer process and eases the fabrication process of polymer tandem solar cells, so that each subcell is fabricated from its optimal solvent and deposition conditions, enabling us to achieve a high ef ciency of 7% for polymer tandem solar cells under AM1.5G spectrum (100 mW/cm 2 ) and 7.8% under lower light intensity (10 mW/cm 2). In addition, considering the importance of layer-by-layer solution
Adv. Mater. 2011, 23, 3465–3470© 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim


wileyonlinelibrary.com
3465

An adaptive coupled-layer visual model for robust visual tracking_IT/计算机_专业资料。作者:Luka Cehovin, Matej Kristan, and Ales Leonardis...
百度文库_文档分享平台 新闻网页贴吧知道音乐图片视频地图百科文库 搜 试试 7 帮助 全部 DOC PPT TXT PDF XLS 百度文库 专业资料 工程科技 信息与通信...
A Survey of Application Layer Techniques for ...environment connecting various networking technologies....is used by the server for achieving adaptability....
connecting with a cable to Thunderbolt products ...The Thunderbolt protocol physical layer is ...achieving high performance between their products ...
百度文库_文档分享平台 新闻网页贴吧知道音乐图片视频地图百科文库 搜 试试 7 帮助 全部 DOC PPT TXT PDF XLS 百度文库 专业资料 工程科技 信息与通信...
热门文档