文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 外语学习 > 英语学习 > Analyzing the effectiveness of an intake compensator for a piston mud pump
侵权投诉

Analyzing the effectiveness of an intake compensator for a piston mud pump

所包括吃饭八角枫

Chemical and Petroleum Engineering, Vol. 31, Nos. 5-6, 1995

RESEARCH, DESIGN, CALCULATIONS ANALYZING THE EFFECTIVENESS OF AN INTAKE

COMPENSATOR FOR A PISTON MUD PUMP M. Ya. Itkis and O. A. Sotnikov

UDC 622.242.6.001.8

The intake compensator of a piston pump increases the suction head and decreases the possibility of cavitation due to decreased inertial losses in the inlet pipe in section 1-2 (see Fig. 1). Physically, the compensator is a gas-filled (air-filled) vessel located ahead of the inlet on the intake side of the pump. The gas cavity is sometimes separated from the liquid by a diaphragm[11. The effectiveness of the compensator is evaluated by the pressure nonuniformity in it, 63[2, 3], which is usually assumed to be equal to the pressure nonuniformity in the intake piping ahead of the compensator: 63= P3max -- P2min= 2 P3max -- P3min, Pay P3max+ P3min (1)

where P3 max, 1)3 rain, and Pay are the maximum, minimum, and average pressure in the compensator. The inertia of the liquid head h23 between the gas cavity of the compensator and the inlet tube, as well as the local resistance in section 2-3, can make the pressure at point 2 of the pipe significantly different from the pressure in the compensator[2]. Therefore the correct way to evaluate the effectiveness of a pipe with a compensator would be in terms of the pressure nonuniformity 62 and the minimum pressure P2 min at point 2, because the intake capacity of the pump increases as P2 min increases and 62 decreases. We now use a mathematical model to analyze the effect of compensator and pipe parameters on the pressure at point 2. The mathematical description of the operation of an intake pipe with a compensator (see Fig. 1) is based on flow continuity at points 2 and 4: Q12= Q23+ Q24;

(2) (3)

Q24= Q5+ Q6+ Q7,

where Qs, Q6, and Q7, the instantaneous flow rates in the corresponding cylinders, are periodic functions of the rotational angle of the pump crank shaft, We substitute Q24 from Eq. (3) into Eq. (2) and differentiate the result with respect to time to obtain dQ12= dQ2a d---'-~~ dQ5+ dQ6+ 'dr dt+ dQ7 dt""

(4)

After we express the derivatives dQ12/dt and dQ23/dt and the compensator flow rate Q23 in terms of the pressure and the coefficients at the corresponding points, we write dQ12 dt

= kl2(Pl -- 9gh -- Y12Q122- P2);

(5)

dQ23= kza(P2 -- pghza -- Yz3Q2Z3 - P3) dt

- 2Qzz3 n d23h23

(6)

Translated from Khimicheskoe i Neftyanoe Mashinostroenie, No. 5, pp. 2-5, May, 1995. 0009-2355/95/0506-0243512.50 9 Plenum Publishing Corporation 243

Analyzing the effectiveness of an intake compensator for a piston mud pump

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email