文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 外语学习 > 其它语言学习 > Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating
侵权投诉

Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating

Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating

Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating Xu Deng,1,2 Lena Mammen,1 Hans-Jürgen Butt,1 Doris Vollmer1*

1Max Planck Institute for Polymer Research, Ackermannweg 10, D-55128, Mainz, Germany. 2Center of Smart Interfaces, Technical University Darmstadt, 64287 Darmstadt, Germany.

*To whom correspondence should be adddressed. E-mail: vollmerd@mpip-mainz.mpg.de

Coating is an essential step in adjusting the surface surface tension of the solid, and γSL is the interfacial tension properties of materials. Superhydrophobic coatings with of the solid liquid interface. For organic liquids (30 ≤ γLV ≤ 18 contact angles greater than 150° and roll-off angles below mN/m) mainly van der Waals interaction act between the 10° for water have been developed, based on low energy molecules. Therefore, γSV- γSL is positive and on planar surfaces and roughness on the nano- and micrometer surfaces Θ < 90°. Similarly, the contact angle on rough scales. However, these surfaces are still wetted by organic surfaces depends on the surface tensions, because roughness liquids such as surfactant-based solutions, alcohols, or amplifies the wetting properties.

alkanes. Coatings that are simultaneously The key factors for superamphiphobicity are not clear yet. superhydrophobic and superoleophobic are rare. We For water repellency, surface roughness and low surface designed an easily fabricated, transparent, and oil-energy are essential (14). To fabricate superamphiphobic rebounding superamphiphobic coating. A porous deposit surfaces overhangs, re-entrant geometry, or convex curvature of candle soot was coated with a 25 nm thick silica shell. is also important (19–25). The complex interplay between The black coating became transparent after calcination at surface roughness, low surface energy and topography has 600°C. After silanization the coating is superamphiphobic made it difficult and expensive to fabricate superamphiphobic and remained so even after its top layer was damaged by surfaces. Tuteja et al. showed that careful design of the sand impingement. topography of a surface allows to construct surfaces with a

A major goal in coating research is to design self-cleaning contact angle for hexadecane close to 160°, although the flat surfaces (1–4). Many surfaces in nature are superhydrophobic surface was oleophilic (19, 23). They explained their – for example lotus leaves (5). Mimicking their surface exceptional oil-repellency by overhang structures and re-morphology led to the development of a number of artificial entrant geometry.

superhydrophobic surfaces (6, 7), opening many applications Here we demonstrate a simple way to make robust, in industrial and biological processes (8–13). Microscopic transparent, superamphiphobic coatings. The surface to be pockets of air are trapped beneath the water drops (14–17). coated, in our case a glass slide, is held above a flame of a This composite interface leads to an increase in the paraffin candle (Fig. 1A). Deposition of a soot layer turns the macroscopic contact angle and a reduced contact angle glass black. Scanning electron microscopy reveals that the hysteresis, enabling water drops to roll off easily, taking dirt soot consists of carbon particles with a typical diameter of 30 with them. However, the addition of an organic liquid such as - 40 nm, forming a loose, fractal-like network (Fig. 1, B and alcohol or oil, decreases the interfacial tension sufficiently to C) (26). A water drop gently deposited on the surface shows a induce homogeneous wetting of the surface. Drops, initially contact angle above 160° and rolls off easily, demonstrating resting on air pockets (Cassie state), pass the transition to the surface’s superhydrophobicity (27). However, the complete wetting (Wenzel state) (14). No naturally occurring structure is fragile as the particle-particle interactions are only surface is known to show a contact angle θ of greater than physical and weak. When water rolls off the surface, the drop 150° and roll-off angles below 10° for water and organic carries soot particles with it until almost all of the soot liquids. These superhydrophobic and superoleophobic deposit is removed and the drop undergoes a wetting surfaces are called superamphiphobic (18). transition (movie S1).

In contrast to superhydrophobicity, the term Inspired by the promising morphology of soot, we “superamphiphobicity” is not uniquely defined in particular developed a technique to coat the soot layer with a silica shell with respect to the liquid used (19–22). According to Young’s making use of chemical vapor deposition (CVD) of equation, cosΘ = (γSV-γSL)/γLV, the lower the surface tension tetraethoxysilane (TES) catalyzed by ammonia. The soot-the higher the tendency of a liquid to spread on a solid surface coated substrates are placed in a desiccator together with two

Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating

(22, 23). Here, Θ is the macroscopic contact angle, γSV is the open glass vessels containing tetraethoxysilane (TES) and

/ doc.guandang.net / 1 December 2011 / Page 1 / 10.1126/science.1207115 Downloaded from doc.guandang.net on December 6, 2011

第1页

你可能喜欢

热门文档

相关文档

  • 超疏水表面涂层的制备

    Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating[J], Science,335,67 (2012). [8] D.K. Sarkar and N. Saleema. One-step ...

  • 超疏水表面涂层的制备

    Candle Soot as a Template for a Transparent Robust Superamphiphobic Coating[J], Science,335,67 (2012). [8] D.K. Sarkar and N. Saleema. One-step ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email