ICL7135C, TLC7135C 4 1/2-DIGIT PRECISION ANALOG-TO-DIGITAL CONVERTERS SLAS074B– DECEMBER 1986– REVISED MAY 1999
D D D D D D D D D D D
Zero Reading for 0-V Input Precision Null Detection With True Polarity at Zero 1-pA Typical Input Current True Differential Input Multiplexed Binary-Coded-Decimal (BCD) Output Low Rollover Error:± 1 Count Max Control Signals Allow Interfacing With UARTs or Microprocessors Autoranging Capability With Over- and Under-Range Signals TTL-Compatible Outputs Direct Replacement for Teledyne TSC7135, Intersil ICL7135, Maxim ICL7135, and Siliconix Si7135 CMOS Technology
DW OR N PACKAGE (TOP VIEW)
VCC– REF ANLG COMMON INT OUT AUTO ZERO BUFF OUT Cref– Cref+ IN– IN+ VCC+ D5 B1 B2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
UNDER RANGE OVER RANGE STROBE RUN/HOLD DGTL GND POLARITY CLK BUSY D1 D2 D3 D4 B8 B4
description The ICL7135C and TLC7135C converters are manufactured with Texas Instruments highly efficient CMOS technology. These 4 1/2-digit, dual-slope-integrating, analog-to-digital converters (DACs) are designed to provide interfaces to both a microprocessor and a visual display. The digit-drive outputs D1 through D4 and multiplexed binary-coded-decimal outputs B1, B2, B4, and B8 provide an interface for LED or LCD decoder/drivers as well as microprocessors. The ICL7135C and TLC7135C offer 50-ppm (one part in 20,000) resolution with a maximum linearity error of one count. The zero error is less than 10µV and zero drift is less than 0.5µV/°C. Source-impedance errors are minimized by low input current (less than 10 pA). Rollover error is limited to± 1 count. The BUSY, STROBE, RUN/HOLD, OVER RANGE, and UNDER RANGE control signals support microprocessor-based measurement systems. The control signals also can support remote data acquisition systems with data transfer through universal asynchronous receiver transmitters (UARTs). The ICL7135C and TLC7135C are characterized for operation from 0°C to 70°C. AVAILABLE OPTIONS PACKAGE TA PLASTIC DIP (N) ICL7135CN TLC7135CN TLC7135CDW SMALL OUTLINE (DW)
0°C to 70°C
Caution. These devices have limited built-in protection. The leads should be shorted together or the device placed in conductive foam during storage or handlilng to prevent electrostatic damage to the MOS gates.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright© 1999, Texas Instruments Incorporated
POST OFFICE BOX 655303
DALLAS, TEXAS 75265

//ICL7135 STROBE signal sbit OVR = P1^4;//ICL7135 Over Range signal sbit UNR = P1^5;//ICL7135 Under Range signal sbit LED = P1^6;//LEDs ...
模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...本系统所设计的四位半数字电压表由 ICL7135(4 1/...共阳极 LED 发光数 码管、 基准电源、 时钟及量程...
共阳极 LED 发光数码管 、基准电源 、时钟及量程...模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...ICL7135 为全 MOS 工艺四位半双积分式 A/D 转换...
ICL7135 和单片机芯片 AT89S52 设计 四位半数字万...LED 点阵显示器件可以显示数字,英文字 符,中文字符...LCD 显示 结束 20 数字万用表设计 三、项目准备 ...
使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...
使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...
ICL7106 3位ADC/驱动LCD ICL7107 3位半ADC/驱动LED ICL7109 4位半ADC/驱动LED ICL7129 4位半ADC/LCD驱动 ICL7135 ADC/LCD驱动BCD输出 ICL7136 3位半CMOS...
使用 LCD1601 液晶模块 显示,并可以与 PC 机进行...通过与LED显示值相比较,其最大偏差即为线性误差。 ...[11] http://www.ic-on-line.com/ ICL7135....
用ICL7135CPL制作高精度... 5页 免费 四位半...LCD 显示电路设计 10 3.信号调理总体设计电路图 10...采用 8 位 LED 动态扫描显示的优点是 能改善外部...
四位半数字电压表【摘要】本文介绍一种数字电压测量电路,该电路采用 ICL7135 ...(4)检查超量程溢出功能,调节输入电压值,当超出测量范围时观察 LED 数 码管...
热门文档