Hydraulic Ram Pumps
Larry M. Curtis,Biosystems Engineer- Soil & Water
Ted W.Tyson, Biosystems Engineer-Irrigation
The hydraulic ram pump is a motorless low-flow-rate pump which uses flowing water as its energy source. The hydraulic ram can be used where small quantities of water are required, such as for domestic water supplies or livestock watering. It is also practical where
conventional power for pumping water is not available, such as remote areas where the
installation of electric service would be uneconomical or where an internal combustion engine would be impractical.
When hydraulic ram pumps are properly sized and installed, flow rates of 14 gallons per minute or 20,000 gallons per day are possible. Water can be lifted to elevations of up to 400 feet, depending upon the quantity and velocity of water flow at the source.
The components of a hydraulic ram pumping system are shown in Figures 1 and 2. They are:
(1) a water supply from a lake, spring, creek, canal, or artesian well; (2) a drive pipe (diverting water from the source to the pump); (3) a hydraulic ram pump; and (4) a delivery pipe to the discharge point.
Principles Of Operation
In a hydraulic ram pump, water flows down the drive pipe to the ram. It is diverted around the pump through an exterior valve until the maximum velocity is obtained for existing flow conditions. When a suitable high velocity is obtained, the valve suddenly closes. Water is
diverted through an interior valve and into the air chamber. The momentum of the flowing fluid forces water into the air chamber under pressure. Water moves into the air tank until the pressure inside the air chamber equalizes and overcomes the driving force behind it. At the proper operating velocity, equilibrium is not approached gradually; rather, the water surges into the tank, compressing the air in the tank, and then the air attempts to rebound. As the rebound, or expansion of compressed air begins, the interior valve closes, trapping the water under pressure in the air tank. That pressure is released as the water flows through the delivery pipe to its destination.
简述水锤泵工作原理 在这个图中,右边粗水管中水流因落差(一般大于 1 米即可)...可以计算水从 2m 高处经粗管进入水锤泵后,突然关闭单向阀 1 产生的最大升高...
简述水锤泵工作原理_能源/化工_工程科技_专业资料。简述水锤泵工作原理有感于刘...可以计算水从 2m 高处经粗管进入水锤泵后, 突然关闭单向阀 1 产生的最大升高...
新型水锤泵设计与研究_机械/仪表_工程科技_专业资料。水锤泵工作的原理结构...供 及 压击由 径 ,___~‘’’‘‘___一 算 0引 言 术锤泵 是一种...
水锤泵的工作原理与应用推广_能源/化工_工程科技_专业资料。适用技术TECHNoLoGY ... 新型水锤泵设计与研究 3页 免费 停泵水锤计算及其防护措... 6页 免费 水锤...
水锤泵_机械/仪表_工程科技_专业资料。水锤泵原理及其应用 1.水锤泵概述 水锤...3.水锤泵的水力学计算 在液压系统中,由于某种原因,液体压力瞬间突然升高,产生...
水锤泵 hydraulic ram pump 水锤泵是一种以流水为动力,通过机械作用,产生水锤... 停泵水锤计算及其防护措... 6页 免费 简述水锤泵工作原理 4页 1下载券 长...
1 停泵水锤的计算原理 停泵水锤的计算有多种方法:图解法、数解法和电算法。其基本原理是按照弹性水柱理论,建立水锤过 程的运动方程和连续方程,这两个方程是双...
使用原理利用流动中的水被突然制动时所产生的能量,使其中一部分水压升到一定高度 的一种泵。图为水锤泵的工作示意。沿进水管向下流动的水流至单向阀A(静重 负载...
1 停泵水锤的计算原理 停泵水锤的计算有多种方法:图解法、数解法和电算法。其基本原理是按照弹性水柱理 论,建立水锤过程的运动方程和连续方程,这两个方程是双...
1 停泵水锤的计算原理 停泵水锤的计算有多种方法:图解法、数解法和电算法。其基本原理是按照弹性水 柱理论,建立水锤过程的运动方程和连续方程,这两个方程是双...
热门文档