文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > MOBILE ROBOT COMPETITIONS FOSTERING ADVANCES IN RESEARCH, DEVELOPMENT AND EDUCATION IN ROBO
侵权投诉

MOBILE ROBOT COMPETITIONS FOSTERING ADVANCES IN RESEARCH, DEVELOPMENT AND EDUCATION IN ROBO

Abstract: Mobile robot competitions are events well suited to experimentation, research and

proportional control). The motors’ speed was not controlled in closed loop. The control loop was closed by the tracking error with respect to the line, only.

The main problem was related to control stability under increasing load caused by the incoming billiard balls. These would represent an increase of about 50% in the robot’s total weight along with an even larger variation in the moment of inertia. The robot would typically lose the track after gathering the 2nd ball when running with the canopy on or the 4th ball when not using the canopy. Nevertheless, it ranked 8th among 14 teams competing in the open category.

This problem was tackled in 1997. The main idea was to maintain the same simple approach (similar motors, electronics and supply) but to reduce the total moment of inertia in order to facilitate the robot’s control. A MATLAB simulator built for this sort of robots [6] allowed to observe a considerable gain in control stability by keeping the moment of inertia as low as possible.

Therefore, the robot named R2D2-v2 used a lift, built just on top of the robot’s centre of mass, to store the billiard balls vertically with a minimum increase in the total moment of inertia. Although this solution was innovative and appealing, its implementation revealed low mechanical reliability, raising problems that were difficult to deal with. The total robot weight increased to about 2.5Kg. The control algorithm was a PID type which, together with the reduction in the moment of inertia, allowed for an improved control performance. The result was, nevertheless, a 5th place among 12 competitors. This was probably the best result that could be achieved with those very low power motors (aprox. 5W). The remaining robots used motors at least 10 times more powerful allowing for much higher speeds. In 1998, the team exchanged categories and entered the monotype competition. In this case, the chassis, motors, wheels and batteries were the same for all teams. The motors were hacked windscreen wiper DC motors, which are considerably powerful (aprox. 60W) and allow to drive the heavier robot (aprox. 18Kg) to speeds of up to 1m/s using 12V supply. Furthermore, the team resulted from a co-operation between the mechanical and electronics engineering departments, which allowed to improve the robot structure and its mechanical subsystems.

The robot was named RUA-v3. The electronic systems were built around an 80C188 processor and the line tracking subsystem was also exchanged by an array of 16 digital IR sensors. The billiard balls capturing subsystem was also redesigned using an active approach based on a rolling sponge to effectively catch the balls. However, the overall mechanical configuration had, again, a large moment of inertia that was thought not to be so restrictive due to the more powerful motors. This belief was wrong. Once again, the robot control, which used a PD type algorithm, was relatively unstable,

4

requiring a very precise tuning of the control gains. Moreover, the tight schedule for building the robot did not allow using closed loop control of the motors’ speeds, as planned. For these reasons, the robot’s average speed had to be severely reduced to about 0.35m/s. Nevertheless, the result was a 5th place among 12 competitors.

In 1999, the same robot was redesigned, mainly by exchanging the placement of several subsystems in order to reduce the total moment of inertia. Furthermore, the closed loop speed control on each motor was also installed. The result, named Zqiub, behaved as expected, tracking the line smoothly with speeds near to 1m/s. It was ranked 3rd on its class, very close to the 2nd robot. Moreover, Zqiub’s modular design together with its stable and regular behaviour were rewarded with the Special Jury Award for the monotype category.

In these activities, students had to deal with issues of control, kynematics, dynamics, electronics, program-ming, etc., in an integrated fashion. Furthermore, there was a constant stress for using modular approaches to ease maintenance, an important topic for students’ future engineering activity. The students’ interest in the field of mobile autonomous robotics has been clearly improved, not only by promoting their participation in this activity, but also in other ones that we have been developing in the university for large number of students (Micro-Rato contest). Several indications seem to confirm that these activities are contributing to improve student´s technical education, in particular, their practical skills to develop embedded control systems for real machines.

3.3. Universidade do Minho - UM

The Group of Automation and Robotics (known as GAR) from the School of Engineering of the University of Minho, located in Guimarães (Portugal), has been developing a team of footballer robots since March 1998. The first team took three months to build the three mobile autonomous robots from scratch (keeper, attacker and a spare one) and these were prepared to participate in the FIST which took place in May 1998 in the city of Bourges (France).

This work started in March 1998, with a team of students made up of Carlos Machado, Sérgio Sampaio and leaded by Fernando Ribeiro. Since then, it has been been continuously improved by the same persons as described in [7] and [8], and this year will participate in their 5th competition.

Each robot was autonomous and there was no communication between them, and had an arc that could be lifted up or pulled down in order to take control of the ball. Each robot had contact sensors all around itself in order to detect collisions with the opponent team robots and also with the short wall placed all around the field. Contact sensors were also used on the ball controlling arc in order to detect when opponent teams had touched that arc willing the take control of the ball in which case the robot would have to lift the arc to allow the opponent

上一页第4页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email