common reason which loads the crack. Stress crack once belong to one more piece of nature of drawing , splitting off , shearing. Stress crack once is loaded and caused, only seldom calculate according to the routine too, but with modern to calculate constant perfection of means, times of stress crack to can accomplish reasonable checking computations too. For example to such stresses 2 times of producing as prestressing force , creeping ,etc., department's finite element procedure calculates levels pole correctly now, but more difficult 40 years ago. In the design, should pay attention to avoiding structure sudden change (or section sudden change), when it is unable to avoid , should do part deal with , corner for instance, make round horn , sudden change office make into the gradation zone transition, is it is it mix muscle to construct to strengthen at the same time, corner mix again oblique to reinforcing bar , as to large hole in a utensil can set up protecting in the perimeter at the terms of having angle steel. Load the crack characteristic in accordance with loading differently and presenting different characteristics differently. The crack appear person who draw more, the cutting area or the serious position of vibration. Must point out , is it get up cover or have along keep into short crack of direction to appear person who press, often the structure reaches the sign of bearing the weight of strength limit, it is an omen that the structure is destroyed, its reason is often that sectional size is partial and small. Receive the strength way differently according to the structure, the crack characteristic produced is as follows: 1, The centre is drawn. The crack runs through the component cross section , the interval is equal on the whole , and is perpendicular to receiving the strength direction. While adopting the whorl reinforcing bar , lie in the second-class crack near the reinforcing bar between the cracks. 2, The centre is pressed. It is parallel on the short and dense parallel crack which receive the strength direction to appear along the component. 3, Receive curved. Most near the large section from border is it appear and draw into direction vertical crack to begin person who draw curved square, and develop toward neutralization axle gradually. While adopting the whorl reinforcing bar , can see shorter second-class crack among the cracks. When the structure matches muscles less, there are few but wide cracks, fragility destruction may take place in the structure 4, Pressed big and partial. Heavy to press and mix person who draw muscle a less
外文文献翻译(土木工程类... 13页 免费 土木工程英语文献原文及... 8页 1... 山东建筑大学毕业设计外文文献及译文 中文译文: 中文译文: 不确定性桥梁车辆...
土木工程毕业设计外文翻... 16页 2下载券 外文翻译,桥梁毕业设计 30页 1...224 KSCE Journal of Civil Engineering 毕业设计——外文翻译 现存的大跨径桥梁...
土木工程毕业设计外文翻译原文_工学_高等教育_教育专区 暂无评价0人阅读0次下载举报文档 土木工程毕业设计外文翻译原文_工学_高等教育_教育专区。土木工程毕业设计...
毕业设计 外文资料翻译原文题目: Composite Box Girder Bridges 译文题目:院系名称: 学生姓名: 指导教师: 混合箱梁桥土木建筑学院 专业班级: 学 熊晓莉 土木工程 ...
土木工程毕业设计外文翻... 16页 2下载券 土木工程英语文献原文及... 8页 1下载券土木工程毕业设计外文翻译...
附录A 专业外文翻译原文 附录 A 专业外文翻译原文 附录 B 专业外文翻译译文 ...以上这三种针对轻质结构的方法已经引领我们进入了千头万绪的桥梁工程 之中。我们...
桥梁二00 九届土木工程(桥梁)专业毕业设计*外文翻译 西班牙灵魂位于西班牙 Zaragoz 埃布罗河上的标志性的混凝土拱桥,目前正在紧张施 工建设中。赫仑·罗素关于...
土木外文翻译原文和译文_建筑/土木_工程科技_专业资料。重庆交通大学土木工程专业(隧道与城市轨道交通工程方向)毕业设计外文翻译 A convection-conduction model for ...
土木工程毕业设计外文翻译_建筑/土木_工程科技_专业...H. Han 摘要 预应力混凝土框架结构通常被用在桥梁... 土木工程英语文献原文及... 8页 1下载券 土木...
沈阳建筑大学毕业设计(论文) 附录一:中文翻译土木工程师 桥梁工程 156 2003 年...(论文) 附录二:翻译原文 Castle Bridge, Weston-Super-Mare, UK Castle Bridge...
热门文档