文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > DVP01PU-H2 安装说明
侵权投诉

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

Warning

9 This instruction sheet provides information on the installation, wiring and trial operation of DVP01PU-H2. For more

detailed information, see “DVP-PLC Application Manual: Special Module”.

9 DO NOT touch any terminal when the power is switched on. Switch off the power before wiring.

9 DVP01PU-H2 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,

humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to oepn the enclosure) in case danger and damage on the device may occur. 9 DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all

the wiring again before switching on the power.

Introduction

Model Explanation and Peripherals

DVP01PU-H2 pulse generation unit is mainly applied to the speed or position control of step or servo drive system. The maximum output pulse of DVP01PU-H2 can be up to 200kPPS. DVP01PU-H2 is built in with various route control modes. Through FROM/TO instructions in DVP-EH2 MPU program, the data in DVP01PU-H2 can be read or written. There are 54 16-bit control registers (CR) in DVP001PU-H2. The 32-bit parameters are composed of 2 continuous CR#.

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

○1 DIN rail (35mm)

○

6 Terminals ○

2 Connection port for extension unit/module ○7 Mounting hole ○3 Model name ○8 I/O terminals

○4 Status indicators ○

9 Connection port for extension unit/module ○

5 DIN rail clip

LED Indicators

POWER : Power indicator, +5V internal power is normal START

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

: Starting input indicator LV : Low voltage indicator (on when the external STOP : Stopping input indicator

power supply is less than19.5V)

DOG : DOG input indicator ERROR : Error indicator (On/Off/flash). Flashes when FP : Forward pulse output indicator CR#44 is not 0.

RP : Reverse pulse output indicator LSP : Right limit input indicator ΦA : MPG A-phase pulse input indicator LSN : Left limit input indicator ΦB : MPG A-phase pulse input indicator PG0

: Zero signal input indicator

CLR : Clearing signal output indicator

I/O Terminal Signals

Type Terminal Description Response feature

Power supply +24V, 0V Power input: 24V DC (-15 ~ +20%), Current consumption: 100mA -

Input

START Starting input 15ms/50ms STOP Stopping input 15ms LSP/LSN Right/left limit input 1ms ΦA+, ΦA- MPG A-phase pulse input +, - (differential signal input) 200kHz ΦB+, ΦB- MPG B-phase pulse input +, - (differential signal input)

200kHz

PG0+, PG0- Zero signal input +, - (differential signal input)

1ms 2 variations according to different operation modes: Input DOG

1. DOG signal when in zero return 1ms 2. Interruption signal inserted in signal-speed or 2-speed sections

CLR+, CLR- Clearing signal (clearing signals in the error counter in servo drive)

130ms Output

FP+, FP- FP/RP mode: forward pulse output; pulse/direction: pulse output;

A/B phase: A phase output 200kHz RP+, RP- FP/RP mode: reverse pulse output; pulse/direction: direction output;

A/B phase: B phase output

200kHz

Wiring

1. Use O-type or Y-type terminals for the I/O wiring as shown in the figure. The torque of

6.8 screw at the PLC terminal should be 5 ~ 8 kg-cm (4.3 ~ 6.9 in-lbs).

2. DO NOT place the wirings of input signals, output signals and power supply in the same

wire conduit.

6.8 3. Use only 60/75°C copper conductors.

I/O Circuit

Specifications

Item

Description

Power supply

24V DC (-15% ~ +20%); Current consumption: 140 ± 30mA, supplied by DVP-EH2 MPU or other self-prepared power supplier

Max. number of

8 modules (axes), which will not occupy any I/O points. DVP-EH2 series MPU is able to connected modules/axes connect to max. a total of 8 extension modules.

Distance Set up by CR. Range: -2,147,483,648 ~ +2,147,483,647; unit: um, mdeg, 10-4 inch, Pulse; multiplications: 100, 101, 102, 103; options: absolute position or relative displacement

Speed

Set up by CR. Range: -2,147,483,648 ~ +2,147,483,647 (10 ~ 200kPPS pulse conversion); unit: pulse/s, cm/min, 10deg/min, inch/min

Isolated by photocoupler. LED indicators for all I/O signals. External output points

Output points FP and RP are differential signal (5V).

Output point CLR is transistor NPN open collector (5 ~ 24V DC, less than 20mA). Isolated by photocoupler. LED indicators for all I/O signals.

Input points START, STOP, LSP, LSN, DOG are contacts or transistor open collector (24V DCExternal input points

± 10%, 5±1mA).

Input points ΦA and ΦB are differential or transistor open collector (5 ~ 24V DC, 6 ~ 15mA) Input points PG0 is differential or transistor open collector (5 ~ 24V DC, 6 ~ 15mA) Pulse output methods In 3 modes: Pulse/Dir, FP (CW)/RP (CCW), A/B; by differential output

Position control program Through FROM/TO instructions in DVP-EH2 MPU program, DVP01PU-H2 is able to read and& data exchange with write the data in the CR. If the data are 32-bit, 2 CRs will be required to process the data. MPU

CR#0 ~ CR#53 are the built-in 16-bit control registers.

When connected to

The modules are numbered from 0 to 7 automatically by their distance from MPU. No. 0 is theDVP-PLC MPU in series

closest to MPU and No. 7 is the furthest. Maximum 8 modules are allowed to connect to MPUand will not occupy any digital I/O points.

Other Specifications

Environment

Operation/storage Operation: 0°C ~ 55°C (temperature); 5 ~ 95% (humidity); pollution degree 2.

Storage: -25°C ~ 70°C (temperature); 5 ~ 95% (humidity)

Vibration/shock immunity

International standards: IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC 68-2-27 (TEST Ea)

Control Registers

CR#

sdesteeHW

LW

urhbContent Setup range

dcitrdattALA #0 H’4190 ○ R Model name Set up by the system. DVP01PU-H2 model code = H’6110 Number of pulses required

#2 #1 H’4191

○ R/W for rotate motor for 1 Range: 1 ~ +2,147,483,647 PPS/REV

revolution (A)

Default = 2,000 pulses/revolution (PLS/REV) #4 #3 H’4193

○ R/W Distance the motor rotates Range: 1 ~ +2,147,483,647 unit/REV for 1 revolution (B)

Default = 1,000 (unit*1/REV)

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

START input polarity

options

#5 H’4195

○ R/W Parameter setting

Default = H’0000

STOP input polarity

START response time

Acceleration curveDOG polarity DOG trigger mode

Revolution direction

Zero return direction

LSN input polarity

LSP input polarity

Pulse output methods

position data

Multiplication of Unit setting

#7 #6 H’4196

○ R/W Maximum speed (VRange: 0 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse

MAX) conversion)*2. Default: 200,000 unit*1

#9 #8 H’4198

○ R/W Bias speed (VBIAS) Range: 0 ~ +2,147,483,647 unit*1 (0 ~ 200kPPS pulse conversion)*2. Default: 0 unit*1

#11 #10 H’419A ○ R/W JOG speed (VRange: 0 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse JOG) conversion)*2. Default: 5,000 unit*1

#13 #12 H’419C ○ R/W Zero return speed (VRange: 0 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse RT) conversion)*2. Default: 50,000 unit*1

#15 #14 H’419E ○ R/W

Zero return deceleration

Range: 0 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse speed (VCR)

conversion)*2. Default: 1,000 unit*1 #16 H’41A0 ○ R/W The number of PG0 in

Range: 0 ~ +32,767PLS zero return mode (N) Default: 0PLS

#17 H’41A1 ○ R/W The number of pulses in Range: -32,768 ~ +32,767PLS zero return mode (P)

Default: 0PLS

#18 H’41A2

○ R/W Zero return mode

b0: zero return mode

(H MODE)

b1: detecting DOG falling edge in zero return mode #20 #19 H’41A3 ○ R/W Setup of zero point (HP)

Range: 0 ~ ±999,999 unit*1. Default: 0 unit*1 #21 H’41A5 ○ R/W Acceleration time (TACC) Range: 10 ~ +32,767ms. Default: 100ms #22 H’41A6 ○ R/W Deceleration time (TDEC)

Range: 10 ~ +32,767ms. Default: 100ms

Range: -2,147,483,648 ~ +2,147,483,647 unit*1

#24 #23 H’41A7 ╳

R/W Target position (I) (P(I)) (-2,147,483,648 ~ +2,147,483,647 pulse conversion) *2. Default: 0 unit*1

#26 #25 H’41A9

╳

R/W Operation speed (I) (V(I))

Range: -2,147,483,648 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse conversion)*2. Default: 1,000 unit*1 Range: -2,147,483,648 ~ +2,147,483,647 unit*1

#28 #27 H’41AB ╳ R/W Target position (II) (P(II))

(-2,147,483,648 ~ +2,147,483,647 pulse conversion)*2. Default: 0 unit*1

CR#

sdesetHW

LW

euContent Setup range rhbdcitrdattALA#30 #29 H’41AD ╳ R/WOperation speed (II) (V(II))

Range: 0 ~ +2,147,483,647 unit*1 (10 ~ 200kPPS pulse

conversion)*2. Default: 2,000 unit*1

b15b14b13b12 b11b10b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

#31 H’41AF ╳ R/W

Operation instruction Default: H’0000

-

CLR output On/Off

CLR signal output mode

Clear CP

-

-

Software START

Absolute position setup

Enabling zero return

Enabling JOG- Enabling JOG+

Stopping reverse pulses

Stopping forward pulses

Software STOP

Error reset

-

b15b14b13b12 b11b10b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

#32 H’41B0

╳ R/WWork mode Default: H’0001

-

-

-

Rest to factory setting

MASK settings

LSP/LSN stop mode

range Manual Pulse Generator STOP mode input operation Manual Pulse Generator Variable speed operation positioning operation Interrupting 2-speed operation 2-speed positioning positioning operation Interrupting single-speed operationSingle-speed positioning

#34 #33 H’41B1 ╳ R/WCurrent position CP (PLS) Range: -2,147,483,648 ~ +2,147,483,647PLS. Default: 0PLS

#36 #35 H’41B3 ╳ R/WCurrent speed CS (PPS) Range: 0 ~ +2,147,483,647PPS.Default: 0PPS #38 #37 H’41B5 ╳ R/W

Current position CP Range: -2,147,483,648~+2,147,483,647 unit*1 (unit*1)

Default: 0 unit*1

#40 #39 H’41B7

╳

R/WCurrent speed CS (unit*1) Range: 0 ~ +2,147,483,647 unit*1. Default: 0 unit*1

Setting up RS-485 communication address. Range: 01 ~ #41 H’41B9

○R/WCommunica-

tion address setting

254.

Default: K1

For setting up communication speed:

4,800/9,600/19,200/38,400/ 57,600/115,200bps.ASCII data format: 7-bit, even bit, 1 stop bit (7, E, 1). RTU data format: 8-bit, even bit, 1 stop bit (8, E, 1).

#42 H’41BA

○R/WCommunication speed

(baud rate) setting

b0: 4,800bps. b1: 9,600 bps (Default).

b2: 19,200bps. b3: 38,400bps. b4: 57,600bps. b5: 115,200bps

b6 ~ b14: reserved. b15: 0=RTU mode; 1=ASCII mode (Default).

b15b14b13b12b11b10b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

#43 H’41BB

╳ R/WExecution status

Default: H’XXXX

-

-

-

-

-

MPG input counting down

MPG input counting up

-

Route pauses

Positioning is completed

Error occurred

CP value overflows

Zero return is completed

progressReverse pulse output inprogressForward pulse outputExecution status in #44 H’41BC ╳ R

Error code

See “q Error Code & Troubleshooting” Default: H’0000 #45 H’41BD ╳ R/W

Numerator of MFG

electronic gearing See explanations below. Default: H’1. #46 H’41BE ╳ R/W

Denominator of MFG

electronic gearing

See explanations below. Default: H’1.

CR#

sdesetHW

LW

ehuContent

Setup range

rcbditrdattALA#48 #47 H’41BF

╳

R/WInput frequency of MPG Input pulse frequency. Default: 0.

Accumulated by the number of pulse input from MPG.

Forward pulse is accumulated by “plus” and reverse pulse #50 #49 H’41C1

╳

R/W

Accumulated number of pulses by MPG

is accumulated by “minus”. The accumulated value will not be affected by the settings in CR#45 and CR#46. Default: 0.

Set value

Response speed The faster the response speed, ≧5 the more synchronous the 4ms (default)instruction pulse output and

#51 H’41C3 ╳ R/W

Response speed of MPG

4 MPG pulse input. The slower the input

32ms 3 response speed, the more 108ms possible the instruction pulse 2 256ms output lags behind MPG pulse 1 or 0

input. (Default: 5)

500ms

bit # Status Description

b0 START input When START input is On, b0=On. b1 STOP input When STOP input is On, b1=On. b2 DOG input When DOG input is On, b2=On. b3

PG0 input When PG0 input is On, b3=On. #52 H’41C4 ╳ R Terminal status

b4 LSP input When LSP input is On, b4=On. b5 LSN input

When LSN input is On, b5=On.

b6 A phase input

When A phase input is On,

b6=On. b7 B phase input

When B phase input is On,

b7=On. b8

CLR output

When CLR output is On, b8=On.

#53 H’41C5 ○R

Firmware version

Displayed in hex; e.g. V1.00 is indicated as H’0100.

*1: The setting of unit is in accordance with b0 and b1 of CR#5.

*2: The module outputs the maximum pulses if the pulse conversion value exceeds the range and outputs the minimum pulses if the

conversion value falls below the range.

CR#0 ~ CR#53: The corresponding parameter addresses H’4190 ~ H’41C5 are for users to read/write data by RS-485 communication. When using RS-485, th e user has to separate the module with MPU first. a. Communication baud rate: 4,800/9,600/19,200/38,400/57,600/115,200bps

b. Modbus ASCII/RTU communication protocols: ASCII data format (7-bit, even bit, 1 stop bit (7, E, 1)); RTU data format (8-bit, even bit, 1 stop bit (8, E, 1)).

c. Function: H’03 (read register data); H’06 (write 1 word datum to register); H’10 (write many word data to register)

d. Latched CR should be written by RS-485 communication to stay latched. CR will not be latched if written by MPU through TO/DTO instruction.

Error Code & Troubleshooting

ERROR LED will be on when hardware malfunction or incorrect parameter settings occur. The error code will

be recorded in CR#44. Error code

Explanation

Error code

Explanation

H’0000 No error H’0014 Incorrect VJOG H’0001 Incorrect target position (I) H’0020 FP is forbidden H’0002 Incorrect target position (II) H’0021 RP is forbidden H’0010 Incorrect operation speed (I) H’0030 Low voltage

H’0011

Incorrect operation speed (II)

H’0080 Hardware error in internal memory H’0012 Incorrect VCR H’0081

Incorrect written in data in internal memory H’0013 Incorrect VRT

注意事項

繁體中文

9 本手冊主要提供DVP01PU-H2定位模組安裝、配線回路及試機之參考,有關進一步的使用說明,請參考DVP-PLC應用技術手冊【特殊模組篇】。

9 請勿在上電時觸摸任何端子。實施配線,務必關閉電源。

9 本機為開放型 (Open Type) 機殼,因此使用者使用本機時,必須將之安裝於具防塵、防潮及免於電擊/衝擊意外之外殼配線箱內。另必須具備保護措施(如:特殊之工具或鑰匙才可打開)防止非維護人員操作或意外衝擊本體,造成危險及損壞。

9 交流輸入電源不可連接於輸入/出信號端,否則將造成嚴重的損壞,請在上電之前再次確認電源配線。

產品簡介

說明及週邊裝置

DVP01PU-H2脈波產生單元主要可應用於步進或伺服驅動系統之速度或位置控制,最高200kPPS脈波輸出,內建多種行程控制模式。透過DVP-PLC EH2系列主機程式以指令FROM/TO來讀寫模組內之資料,模組內具有54個CR暫存器,每個暫存器為16 bits。32位元數值參數由兩個連續編號的CR所組成。

產品外觀 (指示燈、端子台、端子配置)

DVP01PU-H2 安装说明

DVP01PU-H2 安装说明

1 DIN軌糟 (35mm) 6 端子 2 擴充機/擴充模組連接口 7 固定孔 3 機種名稱

8 端子配置

4 電源、錯誤及轉換指示燈 9 擴充機/擴充模組連接座

5 DIN軌固定扣

面板指示燈

POWER :電源指示燈,內部+5V電源正常 START:啟動輸入指示燈 LV

:低電壓指示燈,外部電源輸入小於 STOP :停止輸入指示燈

19.5V,該指示燈亮 DOG :近點信號輸入指示燈 ERROR :錯誤指示燈 (On/Off閃爍),當CR#44 FP :正轉方向脈波輸出指示燈 錯誤編號不為零時動作 RP :反轉方向脈波輸出指示燈 LSP :右極限輸入指示燈 ΦA :手搖輪A相脈波輸入指示燈 LSN :左極限輸入指示燈

ΦB

:手搖輪B相脈波輸入指示燈

PG0

:零點訊號輸入指示燈 CLR :清除信號輸出指示燈

輸入輸出端子信號

種類

端子 說明

響應特性

電源輸入供應 +24V, 0V,

輸入電源,24V DC (-15 ~ +20%),消耗電流100mA -

START 啟動輸入 15ms/50ms

STOP 停止輸入 15ms

LSP/LSN

右極限輸入左極限輸入 1ms

輸入

ΦA+, ΦA- 手搖輪A相脈波輸入+, -(差動信號輸入) 200kHz

ΦB+, ΦB- 手搖輪B相脈波輸入+, -(差動信號輸入) 200kHz PG0+, PG0- 零點訊號輸入+, -(差動信號輸入) 1ms

DOG 依照運轉模式不同有下列2種變化:

1.原點復歸時為近點信號;2.一段速或二段速插入啟動信號 1ms

CLR+, CLR-

清除信號(Servo驅動器內部偏差計數器清除信號) 130ms

正/反轉模式:正轉方向脈波輸出;脈波/方向:脈波輸出端;輸出

FP+, FP- AB相模式:A相輸出

200kHz RP+, RP-

正/反轉模式:反轉方向脈波輸出;脈波/方向:方向輸出端;AB相模式:B相輸出

200kHz

配線

以下

1. 輸出/入配線端請使用O型或Y型端子,端子規格如左所示。PLC端子鏍絲扭力為5 ~ 8 kg-cm(4.3 ~ 6.9 in-lbs)。

2. 在配線時請勿請輸入點信號線與輸出點或電源等動力線置於同一線糟內。

以下

3. 只能使用60/75°C的銅導線

輸入/輸出回路配線

A B 規格

項目

說明

電源輸入

24V DC (-15% ~ +20%) 消耗電流140±30mA;可由DVP-EH2主機取得或自備電源供應器。最大連接台(軸)數 8台(軸);(不佔任何I/O點數,DVP-EH2主機所能連接特殊擴充機台數總和為8台) 距離設定值由控制暫存器來設定

距離值

1. 設定值:-2,147,483,648 ~ +2,147,483,647;2. 單位可選擇:um, mdeg, 10 -4 inch, Pulse;3. 可選擇倍率:10 0, 10 1, 10 2, 10 3;4. 可選擇絕對位置或相對移動量 速度設定值由控制暫存器來設定

速度值

1. 設定值:-2,147,483,648 ~ +2,147,483,647 (10 ~ 200kPPS的脈波轉換值);2. 單位可選擇:pulse/s, cm/min, 10deg/min, inch/min

第1页

你可能喜欢

热门文档

相关文档

  • DVP01PU-H2说明书

    DVP01PU-H2说明书_信息与通信_工程科技_专业资料。DVP01PU-H2说明书...本手册主要提供 DVP01PU-H2 定位模组安装、配线回路及试机之参考,有关进一步的...

  • DVP01PU-H2

    耐振动 / 冲击 电源输入供应 输入 本手册主要提供 01PU 定位模块安装、配线回及试机的参考,有关进一步的使用说明,请参考 DVP-PLC 应 用技术手册【特殊模块篇】...

  • DVP01HC-H2 安装说明

    DVP01HC-H2 安装说明_信息与通信_工程科技_专业资料。PRE DIS YH0, YH1 ...;DVP01HC-H2 机种编码 = H’6120 HW LW #27 CR#27 b0 b1 b2 b3 ...

  • DVPDT02-H2 安装说明

    DVPDT02-H2 安装说明_电子/电路_工程科技_专业资料。Communication Message ...Switch on DVP-EH2, and DVP-EH2 will supply power to DVPDT02-H2. ...

  • DVP08TC-H2 安装说明

    DVP08TC-H2 安装说明_计算机硬件及网络_IT/计算机_专业资料。 ……… ENGLISH...DVP08TC-H2 温度测量模块可接受外部 8 点 0~150mV 电压输入 (热电耦温度...

  • DVPPF02-H2 安装说明

    DVPPF02-H2 安装说明_电子/电路_工程科技_专业资料。Specifications PROFIBUS ...Set the address within the range 0x01 ~ 0x7D and re-power DVP-EH2. ...

  • DVP01安装说明

    01PU 定位模组安装、配线回路及试机之参考,有关进一步的使用说明,请参考“DVP-...H’41A3 #21 H’41A5 #22 H’41A6 #24 #23 H’41A7 ╳ R/W #...

  • 30302646 GST-HX-M8501 8502警报器安装使用说明书F3.92...

    安装、使用产品前, 安装、使用产品前,请阅读安装使用说明书 GST-HXGST-HX-M8501 火灾声警报器 GST-HXGST-HX-M8502 火灾声光警报器 安装使用说明书(Ver.2.0...

  • ...火灾监控探测器安装使用说明书F3.780.652AS V2.03

    1.1 指示灯说明 探测器指示灯 10 GST-DH9500 系列电气火灾监控探测器安装使用说明书 工作灯:绿色,探测器上电后,工作正常,该灯点亮。 报警灯:红色,正常时熄灭,...

  • DVP-PM应用手册

    DVP-PM应用手册_交通运输_工程科技_专业资料。 ...安装配线说明,其它详细之程序设计及指令说明,请参考 ...( D OG3 ) PU LS 1 PU LS 2 SI GN 1 SI ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email