选填,简要介绍文档的主要内容,方便文档被更多人浏览和下载。
Specifications and Ordering Information
Proximitor

Description
Although Proximitor Sensors and interface modules are rugged by design, these units and their electrical connections should be secured and protected when placed near rotating machinery. Also, explosion-proof housings may be necessary for electrical equipment placed in hazardous areas.
Bently Nevada offers three types of housings to protect Proximitor
Sensors, interface modules and velocity-to-displacement converters (VDCs) from adverse environmental conditions. Explosion- proof, water-resistant and water and corrosion-resistant units are available.
Explosion-proof and water-resistant housing
Housings can be ordered with non-conductive mounting plates to electrically isolate the Proximitor Sensors, interface modules and VDCs from the housings. When properly installed, the explosion-proof housing is designed for use in the following: Class 1, Division 1 and 2, Groups C and D. Class II, Division 1 and 2, Groups E, F and G. Class III, Division 1 and 2. Nema 3, 4, 4x, 7 B C D, 9 E F G.
Water-resistant housing
The housings are constructed of 304L stainless steel and are designed to meet NEMA 4 specifications when properly installed.
Water and corrosion-resistant housing
Constructed of fiberglass, the water and corrosion-resistant housing protects Proximitor Sensors, interface modules and VDCs from corrosive and wet environments. When properly installed, the fiberglass housings are designed for outdoor environments because of their resistance to water, dust, corrosion and sleet. Fiberglass housings may not be suitable for areas where Radio Frequency Interference (RFI) is present.
Transducer type options available for all three housings
Housing option (A) allows you to order transducer mounting hardware. The transducer type option includes mounting screws and optional isolation plates to correctly mount and isolate your Proximitor Sensors, interface modules and VDCs.
bently探头防护盒_机械/仪表_工程科技_专业资料。选填,简要介绍文档的主要内容,方便...关于Bently位移探头安装... 3页 2下载券 bently前置器防护盒 7页 1下载券 ...
电涡流传感器系统 振动探头 前置器 延伸电缆(bently 3300 XL英文选型)_能源/化工_工程科技_专业资料。振动探头bently 3300 XL 英文选型 电涡流传感器系统:振动探头...
bently探头防护盒 暂无评价 9页 1下载券 振动位移转速探头效验 63页 1下载券 ...BENTLY 3300 作进行: 2.2.1 利用 24v 稳压电源给前置器供电,24v+和 COM ...
Bently3500 中文手册_专业资料。Bently3500 中文手册1 范围 本规程主要适用于 3500...前置器将其转换为电压信号送至 3500 保护系统进行 处理,处理后由继电器模件输出...
bently位移传感器_工学_高等教育_教育专区。概述 3300 XL 11 mm 电涡流传感器...应用注意事项:虽然前置器的终端和连接器具备静电释放保护功能,但在使用过程中还 ...
下图为探头 测量电压及前置放大器输出电压的过程: 如上面两幅图所示, 前置放大...本特利保护探头安装使用... 38页 免费 Bently3500 中文手册 9页 2下载券 振动...
BENTLY3500/53超速保护系统的防误动措施_专业资料。本文根据对贵州某电厂TSI汽机超速保护误动作的调查分析情况,提出了如何有效防止BENTLY3500/53超速保护系统误动的措...
本特利内华达3300 XL 8mm涡流传感器手册_机械/仪表_工程科技_专业资料。本特利内华达...前置器和接口模块防护箱数据表(部件号 141599-01) 3300 XL 监测器和传感器...
BENTLY探头_机械/仪表_工程科技_专业资料。BENTLY探头BENTLY、BENTLY 探头、BENTLY 传感器, BENTLY 电缆, BENTLY 前置器, BENTLY 探头 上海智川工贸有限公司特价供应...
BENTLY监测系统的安全性分析_机械/仪表_工程科技_专业资料。革新与实践 化工自动...前置器应安装在保 护罩内, 以防机械损伤或弄脏; "保护罩内不应有 金属颗粒等...
热门文档