锂硫电池
Lithium-Sulfur Battery Cathode Enabled by Lithium-Nitrile Interaction
Juchen Guo,* §‖ Zichao Yang, ‖ Yingchao Yu, Héctor D. Abruña and Lynden A. Archer*
School of Chemical and Biomolecular Engineering, Cornell University, Ithaca, NY 14853, United States
Department of Chemistry and Chemical Biology, Cornell University, Ithaca, NY 14853, United States
‖ These authors contributed equally to this work.
Supporting Information
Experimental Section
Synthesis:
All chemicals were purchased from Sigma-Aldrich unless otherwise specified and used without purification. In a typical synthesis, 0.46 g of Li2S was first reacted with 0.64 g of elemental sulfur (1:2 molar ratio) in 5 mL of DMF to form Li2S3 stoichiometrically by vigorous stirring at room temperature. The reaction can be followed colorimetrically. The initial Li2S and DMF mixture has a faint blue color, which quickly turns deep red upon sulfur addition. After stirring at room temperature for 1 h, the solid Li2S completely dissolved in DMF to produce a 2M solution of Li2S3 in DMF. Following preparation of Li2S3 solution, 0.53 g of PAN (MW = 150,000) was dissolved in 5 mL of DMF, which was then mixed with the Li2S3 solution. The molar ratio of Li to acrylonitrile units (nitrile groups) was maintained at 2:1. The resultant mixture of Li2S3 and PAN in DMF was vigorously stirred while heated at 80°C. After approximately 30 mins, the mixture became a deep-red, rigid solid, evidence that the individual PAN chains are strongly cross-linked by interaction with Li-ions.
Characterization:
The crystal structures of the products were characterized using Scintag Theta-theta PAD-X X-Ray Diffractometer (Cu Kα, λ=1.5406 Å). Their morphologies were studied using FEI Tecnai G2 T12 Spirit Transmission Electron Microscope (120kV) and elemental mapping (EDX and EELS) was performed using FEI Tecnai F20 Transmission Electron Microscope (200kV). Thermogravimetric analysis was performed using TA Instruments Q5000 IR Thermogravimetric Analyzer. Raman spectra were collected using a Renishaw InVia Confocal Raman Microscope (laser wavelength = 488nm) with samples containing Li2S sealed in a glass holder. Fourier Transform Infrared Spectra
Sulfur–carbon nano-composite as cathode for rechargeable lithium battery based...1(d). These results suggest that there may be some interaction between ...
. Keywords: cathode materials · hexacyanoferrates · sodium-ion battery [1]...these NMHFCs promising cathodes for SIBs, independent of natural lithium ...
To demonstrate the importance of effective separation between metallic lithium and the sulfur cathode, we measured a Li–S battery in which a ceramic ...
Long-term cyclability of LiFePO4carbon composite cathode material for lithium-ion battery applicatio_工学_高等教育_教育专区。磷酸铁锂Accepted...
LiMn0.6Fe0.4PO4+nanoparticles+as+cathode+material+for+lithium+ion+battery_材料科学_工程科技_专业资料。今日推荐 180份文档 CET...
Size and shape control of LiFePO4 nanocrystals for better lithium ion battery cathode materials_电子/电路_工程科技_专业资料。L一,U上- LU.上UU/I S上二...
Keywords: Lithium ion battery; Surface modi?cation; Cathode materials; Coating Contents 1. LiCoO2 . . . . . . . . . . . . . . . . . . ....
Keywords: Lithium ion battery; LiCoO2; Al2O3; Coating; High potential 1. Introduction As a widely used cathode material for commercial lithium ion ...
Porous carbon-sulfur composite cathode for lithium-sulfur cells 锂硫电池优秀文献锂硫电池优秀文献隐藏>> Electrochemistry Communications 17 (2012) 1–5 Contents...
Acta 50 (2005) 4784–4791 The effect of Al(OH)3 coating on the Li[Li0.2Ni0.2Mn0.6]O2 cathode material for lithium secondary battery Y.-J. Kan...
热门文档