BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS1768:1963
Co-operating organizations
The Mechanical Engineering Industry Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations:
Admiralty*Air Ministry
Engineers
British Chemical Plant Manufacturers’
Association
British Compressed Air Society
British Electrical and Allied Manufacturers’
Association*
British Gear Manufacturers’ AssociationBritish Internal Combustion Engine
Manufacturers’ Association*British Iron and Steel Federation*
British Mechanical Engineering Federation*British Railways Board*
Crown Agents for Oversea Governments and
Administrations
D.S.I.R. — National Engineering LaboratoryElectricity Council, the Generating Board and
the Area Boards in England and WalesEngineering Equipment Users’ Association*
Gas Council
High Commission of India*Institute of Marine EngineersInstitute of Petroleum
Institution of Civil EngineersInstitution of Gas Engineers
Institution of Heating and Ventilating
Engineers
Institution of Mechanical EngineersInstitution of Mechanical Engineers
(Automobile Division)
Institution of Production Engineers*Locomotive and Allied Manufacturers’
Association of Great Britain*London Transport Board
Machine Tool Trades Association*
Ministry of Labour (H.M. Factory Inspectorate)Ministry of Power
Ministry of Public Building and WorksMinistry of TransportNational Coal Board
National Physical Laboratory (D.S.I.R.)*Radio Industry CouncilWar Office*
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
The Government departments and scientific and industrial organizations marked with an asterisk in the above list, together with the following were directly represented on the Committee entrusted with the preparation of this standard:
Agricultural Engineers’ AssociationAssociation of Hydraulic Equipment
Manufacturers
Bright Bolt & Nut Manufacturers AssociationBright Steel Bar Association
British Constructional Steelwork AssociationBritish Cycle & Motor Cycle Industries
Association Limited
Council of British Manufacturers of
Petroleum Equipment
Electronic Engineering Association
Heat Treated Bolt Association
Institute of Iron & Steel Wire ManufacturersMinistry of Aviation
Oil Companies Materials AssociationPost Office
Rolled Thread Screw AssociationScrew Manufacturers AssociationSociety of Motor Manufacturers &
Traders Ltd.
Washer Manufacturers’ AssociationIndividual manufacturers
This British Standard, having been approved by the MechanicalEngineering IndustryStandards
Committeeand endorsed bytheChairman of the Engineering Divisional Council,was published undertheauthority of theGeneralCouncil on17September 1963© BSI 10-1999
First published September 1951First revision September 1963The following BSI references relate to the work on this standard:
Committee reference MEE/60Draft for comment AB(MEE) 4808ISBN 0 580 30789 1
Amendments issued since publicationAmd No.570662235373
Date
December 1965 July 1967April 1988
Indicated by a sideline in the marginComments
标准分享网 doc.guandang.net 免费下载
UN,UNF,UNC,UNEF 英制螺纹区别 英寸制统一螺纹的识别 英寸制统一螺纹,在英寸制国家广泛采用, 该类螺纹分三个系列:粗 牙系列 UNC ,细牙系列 UNF ,特细牙系列...
美制统一螺纹表UNC UNF_机械/仪表_工程科技_专业资料。美制粗细螺纹规格美制标准系列统一螺纹的基本公称 基本大经 牙数 直径 D,d(in) n 6 8 10 12 1/4 5...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
热门文档