聚合物驱 英文
POLYMER FLOODING
Chemical flooding relies on the addition of one or more chemical compounds to an injected fluid either to reduce the interfacial tension between the reservoir oil and the injected fluid or to improve the
sweep efficiency of the injected fluid. There are three general methods in chemical flooding technology. The first is polymer flooding, in which a large macromolecule is used to increase the displacing fluid viscosity. This leads to improved sweep efficiency in the reservoir. The second and third methods, micellar– polymer and alkaline flooding, make use of chemicals that reduce the interfacial tension between an oil and a displacing fluid.
Polymer process
The addition of large-molecular-weight molecules called polymers to an injected water can often increase the effectiveness of a conventional waterflood. Polymers are usually added to the water in concentrations ranging from 250 to 2000 parts per million (ppm).A polymer solution is more viscous than a brine without polymer. In a flooding application, the increased viscosity will alter the mobility ratio between the injected fluid and the reservoir oil. The improved mobility ratio will lead to better vertical and areal sweep efficiencies and thus higher oil recoveries. Polymers have also been used to alter gross permeability variations in some reservoirs. In this application, polymers form a gel-like material by cross-linking with other chemical species.
The polymer gel sets up in large permeability streaks and diverts the flow of any injected fluid to a different location. Two general types of polymers have been used. These are synthetically produced polyacrylamides and biologically produced polysaccharides. Polyacrylamides are long molecules with a small effective diameter. Thus, they are susceptible to mechanical shear. High rates of flow through valves will sometimes break the polymer into smaller entities and reduce the viscosity of the solution. A reduction in viscosity can also occur as the polymer solution tries to squeeze through the pore openings on the sand face of the injection well.
A carefully designed injection scheme is necessary. Polyacrylamides are also sensitive to salt. Large salt concentrations (i.e., greater than 1–2 wt %) tend to make the polymer molecules curl up and lose their viscosity-building effect. Polysaccharides are less susceptible to both mechanical shear and salt. Since they are produced biologically, care must be taken to prevent biological degradation in the reservoir. As a rule, polysaccharides are more expensive than polyacrylamides. Polymer flooding has not been successful in high temperature reservoirs. Neither polymer type has exhibited sufficiently long-term stability above 160 F in moderate-salinity or heavy-salinity brines. Polymer flooding has the best application in moderately heterogeneous reservoirs and reservoirs containing oils with viscosities less than 100 centipoise (cP).
In the United States, there has been a significant increase in the number of active polymer projects since 1978. The projects involve reservoirs having widely differing properties, that is, permeabilities ranging from 20 to 2000 millidarcies (mD), in situ oil viscosities of up to 100 cP, and reservoir
temperatures of up to 200 F. Since the use of polymers does not affect the microscopic displacement efficiency, the improvement in oil recovery will be due to an improved sweep efficiency over what is obtained during a conventional waterflood. Typical oil recoveries from polymer flooding applications are in the range of 1–5% of the initial oil in place. It has been found that operators are more likely to have a successful polymer flood if they start the process early in the producing life of the reservoir.
Surfactant and Surfactant-Polymer Flooding for Enhanced Oil Recovery_能源/化工_工程科技_专业资料。Investigation has been made to characterize the surfactant ...
SPE-104432-Application of EOR Technology by Means of Polymer Flooding in Bohai Oil Fields_能源/化工_工程科技_专业资料。Application of EOR Technology by ...
CURRENT COLLOIDAL DISPERSION GELS ARE NOT SUPERIOR TO POLYMER FLOODING_专业资料 暂无评价
S. (2012). Efficiency of Horizontal and Vertical Well Patterns on the Performance of Micellar-Polymer Flooding in Anisotropic Reservoirs. Energy Science and...
Synthesis of Didodecylmethylcarboxyl Betaine and Its Application in Surfactant–Polymer Flooding 隐藏>> J Surfact Deterg (2012) 15:685–694 DOI 10.1007/...
(2003-2-8 1) 497 碱水驱油方法 alkali/polymer flooding process 对于含有机酸的原油,通过注碱水溶液提高采收率的驱油方法。 (2003-2-8 1) 496 表面活性...
Polymer flooding technology can increase the oil recovery rate by 10% over that of water flooding. Up until Sep. 26, 2006, the accumulative oil ...
polymer flooding 聚合物驱油 pore volume 有限孔隙体积 porosity 孔隙度 porous medium 多孔介质 porous rock 多孔岩石 positive-displacement position 容积式驱替活塞...
polymer flooding 聚合物驱油 pore volume 有限孔隙体积 porosity 孔隙度 porous medium 多孔介质 porous rock 多孔岩石 positive-displacement position 容积式驱替活塞...
热门文档