文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 互联网 > 高速接口设计
侵权投诉

高速接口设计

高速I/O接口设计

■

■Measure refclk, and ensure that it is the correct frequency.Measure the refclk and ensure that the signal complies with the input FPGA

device characteristics—VCM, VOD, VIL, VIH, VMIN, VMAX.

Measure the refclk jitter and ensure that it is within specification.

As PLLs are susceptible to noise, measure the transceiver power supplies to ensure

that they are the correct voltage and that any peak-to-peak noise present on these

supplies is lower than 2% of the nominal setting.■■

rx_pll_locked Does not Assert

If the rx_pll_locked signal does not assert, perform the following checks:

■Debug the refclk (debug similar to the pll_locked signal). Check frequency,

voltage, jitter, transceiver power supply noise.

If the design uses rx_cruclk, debug similar to the pll_inclk and refclk

signal.

1The rx_pll_locked signal may toggle when the CRU is in LTD mode

(rx_freqlocked asserted), which is normal behavior.■

rx_freqlocked Does not Assert

If the rx_freqlocked signal does not assert, perform the following checks:

■Confirm the data received at the pin is the correct data rate as defined in the

ALT2GXB MegaWizard® Plug-In.

Measure the data eye at the receiver and ensure that it complies with the AC

specifications in the relevant device handbook.

Ensure that the jitter on the incoming data is within those specified in the relevant

device handbook.

Increase the PPM setting in the ALT2GXB MegaWizard Plug-In.

Ensure that the received data has enough transitions for the CRU to recover the

clock. Try 8B10B encoding. If the design does not use 8B10B, try transmitting a

constant 0xBC control character. Remember to ensure that it agrees with the

ALT2GXB MegaWizard Plug-In.

Try looping the transmitter back onto the receiver via a cable or one of the on-chip

serial loopback modes. This powerful debug tool ensures that the received data is

0 PPM from the transmitter refclk. Using on-chip serial loopback also eliminates

possible PCB routing causes.

Check that the cal_blk_clk is within defined frequency limits. The

cal_blk_clk calculates the transceiver on-chip termination.

Measure the RREFB pin for noise. This pin defines a bias voltage for transceiver

on-chip termination.■■■■■■■

Received Data has Errors

If erroneous data is received, or the rx_errdetect or rx_disperr signals are

asserted, perform the following checks:

上一页第18页

你可能喜欢

  • 软件接口设计
  • 接口设计说明
  • 接口设计文档
  • 接口设计方案
  • 接口设计规范
  • 接口技术课程设计

热门文档

相关文档

  • 高速USB接口设计

    第17卷V01.17 第3期No.3 电子设计工程ElectronicDesignEngineering 2009年3月Mat.2009 高速USB接口设计甄国涌.张森峰(中北大学电子潮试技术国家重点实验室,山西...

  • 高速USB接口设计

    第17 卷 第3期 Vol.17 No.3 电子设计工程 Electronic Design Engineering 2009 年 3 月 Mar.2009 高速 USB 接口设计甄国涌 , 张森峰(中北大学 电子测试技术...

  • DDR+SDRAM与FPGA的高速接口设计

    DDR+SDRAM与FPGA的高速接口设计_信息与通信_工程科技_专业资料。介绍关于FPGA DDR 控制器的专业文档可轴糕器件盛.属 DDR 电子测豢技术 ELECTR()NIC 第3l卷第n...

  • 基于Xilinx Spartan6的高速接口设计

    基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业...

  • TS201高速通信接口设计及实现

    ADI公司TigerSHARC系列DSP芯片TS201性能优越,在高速实时信号处理中得到广泛应用,而其中对TS201的通信接口设计成为保证其高速实时性能的关键。对TS201与FPGA之间两种主要...

  • STM32F103的高速以太网接口设计

    STM32F103的高速以太网接口设计_计算机硬件及网络_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 STM32F103的高速以太网接口设计_计算机硬件及网络_IT/...

  • 基于STM32F107的高速以太网接口设计与应用

    基于STM32F107的高速以太网接口设计与应用_工学_高等教育_教育专区。基于STM32F107的高速以太网接口设计与应用Network and Multimedi 文章编号: 1002-8684 (2011) 09...

  • 【论文】Gbps试验系统中高速串行接口的设计与实现

    Gbps试验系统中高速串行接口的设计与实现_专业资料。介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据...

  • 基于FPGA的高速通信接口设计

    基于FPGA的高速通信接口设计_信息与通信_工程科技_专业资料。基于FPGA的高速通信接口设计2005年9月 第3期 实验科学与技术 基于FPGA的高速通信接口设计。 A砸ghSpeed...

  • 基于TMS320C6455的高速SRIO接口设计

    基于TMS320C6455的高速SRIO接口设计_信息与通信_工程科技_专业资料。RapidIO互连架构是一个开放的标准,满足了嵌入式基础设施在应用方面的广泛需要。它将是未来十几年嵌...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email